RFC 8913 TWAMP YANG Data Model November 2021
Civil, et al. Standards Track [Page]
Stream:
Internet Engineering Task Force (IETF)
RFC:
8913
Category:
Standards Track
Published:
ISSN:
2070-1721
Authors:
R. Civil
Ciena Corporation
A. Morton
AT&T Labs
R. Rahman
M. Jethanandani
Xoriant Corporation
K. Pentikousis, Ed.
Detecon

RFC 8913

Two-Way Active Measurement Protocol (TWAMP) YANG Data Model

Abstract

This document specifies a data model for client and server implementations of the Two-Way Active Measurement Protocol (TWAMP). This document defines the TWAMP data model through Unified Modeling Language (UML) class diagrams and formally specifies it using the YANG data modeling language (RFC 7950). The data model is compliant with the Network Management Datastore Architecture (NMDA).

Status of This Memo

This is an Internet Standards Track document.

This document is a product of the Internet Engineering Task Force (IETF). It represents the consensus of the IETF community. It has received public review and has been approved for publication by the Internet Engineering Steering Group (IESG). Further information on Internet Standards is available in Section 2 of RFC 7841.

Information about the current status of this document, any errata, and how to provide feedback on it may be obtained at https://www.rfc-editor.org/info/rfc8913.

Table of Contents

1. Introduction

The Two-Way Active Measurement Protocol (TWAMP) [RFC5357] is used to measure network performance parameters such as latency, bandwidth, and packet loss by sending probe packets and measuring their experience in the network. To date, TWAMP implementations do not come with a standard management framework, and, as such, implementers have no choice except to provide a proprietary mechanism. This document addresses this gap by defining the model using Unified Modeling Language (UML) class diagrams [UML] and formally specifying a TWAMP data model that is compliant with the Network Management Datastore Architecture (NMDA) [RFC8342], using YANG 1.1 [RFC7950].

1.1. Motivation

In current TWAMP deployments, the lack of a standardized data model limits the flexibility to dynamically instantiate TWAMP-based measurements across equipment from different vendors. In large, virtualized, and dynamically instantiated infrastructures where network functions are placed according to orchestration algorithms, proprietary mechanisms for managing TWAMP measurements pose severe limitations with respect to programmability.

Two major trends call for standardizing TWAMP management aspects. First, it is expected that in the coming years large-scale and multi-vendor TWAMP deployments will become the norm. From an operations perspective, using several vendor-specific TWAMP configuration mechanisms when one standard mechanism could provide an alternative is expensive and inefficient. Second, the increasingly software-defined and virtualized nature of network infrastructures, based on dynamic service chains [NSC] and programmable control and management planes [RFC7426], requires a well-defined data model for TWAMP implementations. This document defines such a TWAMP data model and specifies it formally using the YANG 1.1 data modeling language [RFC7950].

1.2. Terminology

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here.

1.3. Document Organization

The rest of this document is organized as follows. Section 2 presents the scope and applicability of this document. Section 3 provides a high-level overview of the TWAMP data model. Section 4 details the configuration parameters of the data model, and Section 5 specifies in YANG the TWAMP data model. Section 6 lists illustrative examples that conform to the YANG data model specified in this document. Appendix A elaborates these examples further.

2. Scope, Model, and Applicability

The purpose of this document is the specification of a vendor-independent data model for TWAMP implementations.

Figure 1 illustrates a redrawn version of the TWAMP logical model found in Section 1.2 of TWAMP [RFC5357]. The figure is annotated with pointers to the UML diagrams [UML] provided in this document and associated with the data model of the four logical entities in a TWAMP deployment, namely the TWAMP Control-Client, Server, Session-Sender, and Session-Reflector. A UML Notation Guide is available in Section 5 of UML [UML].

As per TWAMP [RFC5357], unlabeled links in Figure 1 are left unspecified and may be proprietary protocols.

         (Figure 3)                              (Figure 4)
     +----------------+                          +--------+
     | Control-Client |  <-- TWAMP-Control -->   | Server |
     +----------------+                          +--------+
             ^                                        ^
             |                                        |
             V                                        V
     +----------------+                     +-------------------+
     | Session-Sender |  <-- TWAMP-Test --> | Session-Reflector |
     +----------------+                     +-------------------+
         (Figure 5)                               (Figure 6)
Figure 1: Annotated TWAMP Logical Model

As per TWAMP [RFC5357], a TWAMP implementation may follow a simplified logical model, in which the same node acts as both Control-Client and Session-Sender, while another node acts at the same time as both TWAMP Server and Session-Reflector. Figure 2 illustrates this simplified logical model and indicates the interaction between the TWAMP configuration client and server using, for instance, NETCONF [RFC6241] or RESTCONF [RFC8040].

  o-------------------o                       o-------------------o
  |   Config client   |                       |   Config client   |
  o-------------------o                       o-------------------o
           ||                                          ||
   NETCONF || RESTCONF                         NETCONF || RESTCONF
           ||                                          ||
  o-------------------o                       o-------------------o
  |   Config server   |                       |   Config server   |
  | (Figures 3 and 5) |                       | (Figures 4 and 6) |
  +-------------------+                       +-------------------+
  |   Control-Client  | <-- TWAMP-Control --> |      Server       |
  |                   |                       |                   |
  |   Session-Sender  |  <-- TWAMP-Test -->   | Session-Reflector |
  +-------------------+                       +-------------------+
Figure 2: Simplified TWAMP Model and Protocols

The data model defined in this document is orthogonal to the specific protocol used between the Config client and Config server to communicate the TWAMP configuration parameters.

Operational actions such as how TWAMP-Test sessions are started and stopped, how performance measurement results are retrieved, or how stored results are cleared, and so on, are not addressed by the configuration model defined in this document. As noted above, such operational actions are not part of the TWAMP specification [RFC5357] and hence are out of scope for this document. See also Appendix B. In addition, for operational state, the information provided in the Performance Metrics Registry [RFC8911] and [PERF-METRICS] can be used to develop an independent model for the Performance Metrics that need to be captured and retrieved.

3. Data Model Overview

The TWAMP data model includes four categories of configuration items.

First, global configuration items relate to parameters that are set on a per-device level. For example, the administrative status of the device with respect to whether it allows TWAMP sessions and, if so, in what capacity (e.g., Control-Client, Server, or both) is a typical instance of a global configuration item.

A second category includes attributes that can be configured on a per‑TWAMP-Control-connection basis, such as the Server IP address.

A third category includes attributes related to per-TWAMP-Test-session attributes -- for instance, setting different values in the Differentiated Services Code Point (DSCP) field.

Finally, the data model includes attributes that relate to the operational state of the TWAMP implementation.

As the TWAMP data model is described in the remaining sections of this document, readers should keep in mind the functional entity grouping illustrated in Figure 1.

3.1. Control-Client

A TWAMP Control-Client has an administrative status field set at the device level that indicates whether the node is enabled to function as such.

Each TWAMP Control-Client is associated with zero or more TWAMP‑Control connections. The main configuration parameters of each control connection are:

  • A name that can be used to uniquely identify at the Control-Client a particular control connection. This name is necessary for programmability reasons because at the time of creation of a TWAMP-Control connection not all IP and TCP port number information needed to uniquely identify the connection is available.
  • The IP address of the interface the Control-Client will use for connections.
  • The IP address of the remote TWAMP Server.
  • Authentication and encryption attributes such as KeyID, Token, and the Control-Client Initialization Vector (Client-IV); see also Section 3.1 of "A One-way Active Measurement Protocol (OWAMP)" [RFC4656] and "Randomness Requirements for Security" [RFC4086].

Each TWAMP-Control connection, in turn, is associated with zero or more TWAMP-Test sessions. For each test session, the following configuration items should be noted:

  • The test session name, which uniquely identifies a particular test session at the Control-Client and Session-Sender. Similar to the control connections mentioned above, this unique test session name is needed because at the time of creation of a TWAMP-Test session, for example, the source UDP port number is not known to uniquely identify the test session.
  • The IP address and UDP port number of the Session-Sender on the path under test by TWAMP.
  • The IP address and UDP port number of the Session-Reflector on said path.
  • Information pertaining to the test packet stream, such as the test starting time; which Performance Metric is to be used, as defined in "Registry for Performance Metrics" [RFC8911]; or whether the test should be repeated.

3.2. Server

Each TWAMP Server has an administrative status field set at the device level to indicate whether the node is enabled to function as a TWAMP Server.

Each Server is associated with zero or more TWAMP-Control connections. Each control connection is uniquely identified by the 4-tuple {Control-Client IP address, Control-Client TCP port number, Server IP address, Server TCP port}.  Control connection configuration items on a TWAMP Server are read-only.

3.3. Session-Sender

A TWAMP Session-Sender has an administrative status field set at the device level that indicates whether the node is enabled to function as such.

There is one Session-Sender instance for each TWAMP-Test session that is initiated from the sending device. Primary configuration fields include:

  • The test session name, which MUST be identical to the corresponding test session name on the TWAMP Control-Client (Section 3.1).
  • The control connection name, which, along with the test session name, uniquely identifies the TWAMP Session-Sender instance.
  • Information pertaining to the test packet stream, such as the number of test packets and the packet distribution to be employed; see also "Network performance measurement with periodic streams" [RFC3432].

3.4. Session-Reflector

Each TWAMP Session-Reflector has an administrative status field set at the device level to indicate whether the node is enabled to function as such.

Each Session-Reflector is associated with zero or more TWAMP-Test sessions. For each test session, the REFWAIT timeout parameter, which determines whether to discontinue the session if no packets have been received (TWAMP [RFC5357], Section 4.2), can be configured.

Read-only access to other data model parameters, such as the Sender IP address, is foreseen. Each test session can be uniquely identified by the 4-tuple mentioned in Section 3.2.

4. Data Model Parameters

This section defines the TWAMP data model using UML [UML] and introduces selected parameters associated with the four TWAMP logical entities. The complete TWAMP data model specification is provided in the YANG module presented in Section 5.2.

4.1. Control-Client

The client container (see Figure 3) holds items that are related to the configuration of the TWAMP Control-Client logical entity (recall Figure 1).

The client container includes an administrative configuration parameter (client/admin-state) that indicates whether the device is allowed to initiate TWAMP-Control connections.

  +-------------+
  | client      |
  +-------------+                   1..* +-----------------------+
  | admin-state |<>----------------------| mode-preference-chain |
  |             |                        +-----------------------+
  |             |  1..* +------------+   | priority              |
  |             |<>-----| key-chain  |   | mode                  |
  +-------------+       +------------+   +-----------------------+
         ^              | key-id     |
         V              | secret-key |
         |              +------------+
         | 0..*
  +------------------------+
  | ctrl-connection        |
  +------------------------+
  | name                   |
  | client-ip              |
  | server-ip              |
  | server-tcp-port        |    0..* +----------------------+
  | control-packet-dscp    |<>-------| test-session-request |
  | key-id                 |         +----------------------+
  | max-count              |         | name                 |
  | client-tcp-port   {ro} |         | sender-ip            |
  | server-start-time {ro} |         | sender-udp-port      |
  | state             {ro} |         | reflector-ip         |
  | selected-mode     {ro} |         | reflector-udp-port   |
  | token             {ro} |         | timeout              |
  | client-iv         {ro} |         | padding-length       |
  +------------------------+         | test-packet-dscp     |
                                     | start-time           |
              +-------------+ 1      | repeat               |
              | pm-reg-list |------<>| repeat-interval      |
              +-------------+        | state           {ro} |
              | pm-index    |        | sid             {ro} |
              +-------------+        +----------------------+
Figure 3: TWAMP Control-Client UML Class Diagram

The client container holds a list (mode-preference-chain) that specifies the mode values according to their preferred order of use by the operator of this Control-Client, including the authentication and encryption modes. Specifically, mode-preference-chain lists the mode and its corresponding priority, expressed as a 16-bit unsigned integer. Values for the priority start with zero, the highest priority, and decreasing priority value is indicated by every increase in value by one.

Depending on the modes available in the Server Greeting, the Control-Client MUST choose the highest-priority mode from the configured mode-preference-chain list.

Note that the list of preferred modes may set multiple bit positions independently, such as when referring to the extended TWAMP features in "Mixed Security Mode for the Two-Way Active Measurement Protocol (TWAMP)" [RFC5618], "Individual Session Control Feature for the Two-Way Active Measurement Protocol (TWAMP)" [RFC5938], "Two-Way Active Measurement Protocol (TWAMP) Reflect Octets and Symmetrical Size Features" [RFC6038], and "IKEv2-Derived Shared Secret Key for the One-Way Active Measurement Protocol (OWAMP) and Two-Way Active Measurement Protocol (TWAMP)" [RFC7717]. If the Control-Client cannot determine an acceptable mode, or when the bit combinations do not make sense, e.g., authenticated and unauthenticated bits are both set, it MUST respond with zero Mode bits set in the Set-Up-Response message, indicating that it will not continue with the control connection.

In addition, the client container holds a list named "key-chain", which relates key-id with the respective secret-key. Both the Server and the Control-Client use the same mappings from key-id to secret‑key (in Figure 3); in order for this to work properly, key-id must be unique across all systems in the administrative domain. The Server, being prepared to conduct sessions with more than one Control-Client, uses key-id to choose the appropriate secret-key; a Control-Client would typically have different secret keys for different Servers. The secret-key is the shared secret, of type "binary", and the length SHOULD contain at least 128 bits of entropy. The key-id and secret-key encoding SHOULD follow Section 9.8 of YANG [RFC7950]. The derived key length (dkLen as defined in "PKCS #5: Password-Based Cryptography Specification Version 2.1" [RFC8018]) MUST be 16 octets for the AES Session-key used for encryption and 32 octets for the HMAC-SHA1 Session-key used for authentication; see also Section 6.10 of OWAMP [RFC4656].

Each client container also holds a list of control connections, where each item in the list describes a TWAMP-Control connection initiated by this Control-Client. There SHALL be one ctrl-connection per TWAMP-Control (TCP) connection that is to be initiated from this device.

In turn, each ctrl-connection holds a test-session-request list. Each test-session-request holds information associated with the Control-Client for this test session. This includes information associated with the Request-TW-Session/Accept-Session message exchange (see Section 3.5 of TWAMP [RFC5357]).

There SHALL be one instance of test-session-request for each TWAMP‑Test session that is to be negotiated by this TWAMP-Control connection via a Request-TW-Session/Accept-Session exchange.

The Control-Client is also responsible for scheduling TWAMP-Test sessions; therefore, test-session-request holds information related to these actions (e.g., pm-index, repeat-interval).

4.2. Server

The server container (see Figure 4) holds items that are related to the configuration of the TWAMP Server logical entity (recall Figure 1).

The server container includes an administrative configuration parameter (server/admin-state) that indicates whether the device is allowed to receive TWAMP-Control connections.

A device operating in the Server Role cannot configure attributes on a per-TWAMP-Control-connection basis, as it has no foreknowledge of the incoming TWAMP-Control connections to be received. Consequently, any parameter that the Server might want to apply to an incoming control connection must be configured at the overall Server level and applied to all incoming TWAMP-Control connections.

    +---------------------+
    | server              |
    +---------------------+
    | admin-state         |   1..* +------------+
    | server-tcp-port     |<>------| key-chain  |
    | servwait            |        +------------+
    | control-packet-dscp |        | key-id     |
    | count               |        | secret-key |
    | max-count           |        +------------+
    | modes               |
    |                     |   0..* +--------------------------+
    |                     |<>------| ctrl-connection          |
    +---------------------+        +--------------------------+
                                   | client-ip           {ro} |
                                   | client-tcp-port     {ro} |
                                   | server-ip           {ro} |
                                   | server-tcp-port     {ro} |
                                   | state               {ro} |
                                   | control-packet-dscp {ro} |
                                   | selected-mode       {ro} |
                                   | key-id              {ro} |
                                   | count               {ro} |
                                   | max-count           {ro} |
                                   | salt                {ro} |
                                   | server-iv           {ro} |
                                   | challenge           {ro} |
                                   +--------------------------+
Figure 4: TWAMP Server UML Class Diagram

Each server container holds a list named "key-chain", which relates key-id with the respective secret-key. As mentioned in Section 4.1, both the Server and the Control-Client use the same mapping from key‑id to the shared secret-key; in order for this to work properly, key-id must be unique across all the systems in the administrative domain. The Server, being prepared to conduct sessions with more than one Control-Client, uses key-id to choose the appropriate secret-key; a Control-Client would typically have different secret keys for different Servers.  key-id tells the Server which shared secret-key the Control-Client wishes to use for authentication or encryption.

Each incoming control connection active on the Server is represented by a ctrl-connection. There SHALL be one ctrl-connection per incoming TWAMP-Control (TCP) connection that is received and active on the Server. Each ctrl-connection can be uniquely identified by the 4-tuple {client-ip, client-tcp-port, server-ip, server-tcp-port}.  All items in the ctrl-connection list are read-only.

4.3. Session-Sender

The session-sender container, illustrated in Figure 5, holds items that are related to the configuration of the TWAMP Session-Sender logical entity.

The session-sender container includes an administrative parameter (session-sender/admin-state) that controls whether the device is allowed to initiate TWAMP-Test sessions.

      +----------------+
      | session-sender |
      +----------------+  0..* +---------------------------+
      | admin-state    |<>-----| test-session              |
      +----------------+       +---------------------------+
                               | name                      |
                               | ctrl-connection-name {ro} |
                               | fill-mode                 |
                               | number-of-packets         |
                               | state                {ro} |
                               | sent-packets         {ro} |
                               | rcv-packets          {ro} |
                               | last-sent-seq        {ro} |
                               | last-rcv-seq         {ro} |
                               +---------------------------+
                                            ^
                                            V
                                            | 1
                                +---------------------+
                                | packet-distribution |
                                +---------------------+
                                | periodic / poisson  |
                                +---------------------+
                                    |           |
                         +-------------------+  |
                         | periodic-interval |  |
                         +-------------------+  |
                                                |
                                        +--------------+
                                        | lambda       |
                                        | max-interval |
                                        +--------------+
Figure 5: TWAMP Session-Sender UML Class Diagram

Each TWAMP-Test session initiated by the Session-Sender will be represented by an instance of a test-session object. There SHALL be one instance of test-session for each TWAMP-Test session for which packets are being sent.

4.4. Session-Reflector

The session-reflector container, illustrated in Figure 6, holds items that are related to the configuration of the TWAMP Session-Reflector logical entity.

The session-reflector container includes an administrative parameter (session-reflector/admin-state) that controls whether the device is allowed to respond to incoming TWAMP-Test sessions.

A device operating in the Session-Reflector Role cannot configure attributes on a per-session basis, as it has no foreknowledge of what incoming sessions it will receive. As such, any parameter that the Session-Reflector might want to apply to an incoming TWAMP-Test session must be configured at the overall Session-Reflector level and applied to all incoming sessions.

             +-------------------+
             | session-reflector |
             +-------------------+
             | admin-state       |
             | refwait           |
             +-------------------+
                      ^
                      V
                      |
                      | 0..*
             +----------------------------------------+
             | test-session                           |
             +----------------------------------------+
             | sid                               {ro} |
             | sender-ip                         {ro} |
             | sender-udp-port                   {ro} |
             | reflector-ip                      {ro} |
             | reflector-udp-port                {ro} |
             | parent-connection-client-ip       {ro} |
             | parent-connection-client-tcp-port {ro} |
             | parent-connection-server-ip       {ro} |
             | parent-connection-server-tcp-port {ro} |
             | test-packet-dscp                  {ro} |
             | sent-packets                      {ro} |
             | rcv-packets                       {ro} |
             | last-sent-seq                     {ro} |
             | last-rcv-seq                      {ro} |
             +----------------------------------------+
Figure 6: TWAMP Session-Reflector UML Class Diagram

Each incoming TWAMP-Test session that is active on the Session-Reflector SHALL be represented by an instance of a test-session object. All items in the test-session object are read-only.

Instances of test-session are indexed by a Session Identifier (SID) (the sid parameter). This SID value is auto-allocated by the TWAMP Server as test session requests are received and is communicated back to the Control-Client in the SID field of the Accept-Session message; see Section 4.3 of "Two-Way Active Measurement Protocol (TWAMP) Reflect Octets and Symmetrical Size Features" [RFC6038].

When attempting to retrieve operational data for active test sessions from a Session-Reflector device, the user will not know what sessions are currently active on that device or what SIDs have been auto‑allocated for these test sessions. If the user has network access to the Control-Client device, then it is possible to read the data for this session under client/ctrl-connection/test-session-request/sid and obtain the SID (see Figure 3). The user may then use this SID value as an index to retrieve an individual session-reflector/test-session instance on the Session-Reflector device.

If the user has no network access to the Control-Client device, then the only option is to retrieve all test-session instances from the Session-Reflector device and then pick out specific test-session instances of interest to the user. This could be problematic if a large number of test sessions are currently active on that device.

Each Session-Reflector TWAMP-Test session contains the following 4-tuple: {parent-connection-client-ip, parent-connection-client-tcp-port, parent-connection-server-ip, parent-connection-server-tcp-port}.  This 4-tuple MUST correspond to the equivalent 4-tuple {client-ip, client-tcp-port, server-ip, server-tcp-port} in server⁠/ctrl-connection. This 4-tuple allows the user to trace back from the TWAMP-Test session to the (parent) TWAMP-Control connection that negotiated this test session.

5. Data Model

This section formally specifies the TWAMP data model using YANG.

5.1. YANG Tree Diagram

This section presents a simplified graphical representation of the TWAMP data model using a YANG tree diagram. Readers should keep in mind that the limit of 72 characters per line forces us to introduce artificial line breaks in some tree diagram nodes. Tree diagrams used in this document follow the notation defined in "YANG Tree Diagrams" [RFC8340].

Please note that the backslash ('\') character near the end of the diagram is used for formatting purposes only (i.e., "reflector‑udp‑port]" should be treated as part of the same line as "[sender‑ip sender‑udp‑port reflector‑ip").

module: ietf-twamp
  +--rw twamp
     +--rw client {control-client}?
     |  +--rw admin-state?             boolean
     |  +--rw mode-preference-chain* [priority]
     |  |  +--rw priority    uint16
     |  |  +--rw mode?       twamp-modes
     |  +--rw key-chain* [key-id]
     |  |  +--rw key-id        string
     |  |  +--rw secret-key?   binary
     |  +--rw ctrl-connection* [name]
     |     +--rw name                    string
     |     +--rw client-ip?              inet:ip-address
     |     +--rw server-ip               inet:ip-address
     |     +--rw server-tcp-port?        inet:port-number
     |     +--rw control-packet-dscp?    inet:dscp
     |     +--rw key-id?                 string
     |     +--rw max-count-exponent?     uint8
     |     +--ro client-tcp-port?        inet:port-number
     |     +--ro server-start-time?      uint64
     |     +--ro repeat-count?           uint64
     |     +--ro state?
     |     |       control-client-connection-state
     |     +--ro selected-mode?          twamp-modes
     |     +--ro token?                  binary
     |     +--ro client-iv?              binary
     |     +--rw test-session-request* [name]
     |        +--rw name                  string
     |        +--rw sender-ip?            inet:ip-address
     |        +--rw sender-udp-port?      union
     |        +--rw reflector-ip          inet:ip-address
     |        +--rw reflector-udp-port?   inet:port-number
     |        +--rw timeout?              uint64
     |        +--rw padding-length?       uint32
     |        +--rw test-packet-dscp?     inet:dscp
     |        +--rw start-time?           uint64
     |        +--rw repeat?               uint32
     |        +--rw repeat-interval?      uint32
     |        +--rw pm-reg-list* [pm-index]
     |        |  +--rw pm-index    uint16
     |        +--ro state?                test-session-state
     |        +--ro sid?                  string
     +--rw server {server}?
     |  +--rw admin-state?           boolean
     |  +--rw server-tcp-port?       inet:port-number
     |  +--rw servwait?              uint32
     |  +--rw control-packet-dscp?   inet:dscp
     |  +--rw count?                 uint8
     |  +--rw max-count-exponent?    uint8
     |  +--rw modes?                 twamp-modes
     |  +--rw key-chain* [key-id]
     |  |  +--rw key-id        string
     |  |  +--rw secret-key?   binary
     |  +--ro ctrl-connection*
     |          [client-ip client-tcp-port server-ip server-tcp-port]
     |     +--ro client-ip              inet:ip-address
     |     +--ro client-tcp-port        inet:port-number
     |     +--ro server-ip              inet:ip-address
     |     +--ro server-tcp-port        inet:port-number
     |     +--ro state?                 server-ctrl-connection-state
     |     +--ro control-packet-dscp?   inet:dscp
     |     +--ro selected-mode?         twamp-modes
     |     +--ro key-id?                string
     |     +--ro count?                 uint8
     |     +--ro max-count-exponent?    uint8
     |     +--ro salt?                  binary
     |     +--ro server-iv?             binary
     |     +--ro challenge?             binary
     +--rw session-sender {session-sender}?
     |  +--rw admin-state?    boolean
     |  +--rw test-session* [name]
     |     +--rw name                    string
     |     +--ro ctrl-connection-name?   string
     |     +--rw fill-mode?              padding-fill-mode
     |     +--rw number-of-packets       uint32
     |     +--rw (packet-distribution)?
     |     |  +--:(periodic)
     |     |  |  +--rw periodic-interval       decimal64
     |     |  +--:(poisson)
     |     |     +--rw lambda                  decimal64
     |     |     +--rw max-interval?           decimal64
     |     +--ro state?                  sender-session-state
     |     +--ro sent-packets?           uint32
     |     +--ro rcv-packets?            uint32
     |     +--ro last-sent-seq?          uint32
     |     +--ro last-rcv-seq?           uint32
     +--rw session-reflector {session-reflector}?
        +--rw admin-state?    boolean
        +--rw refwait?        uint32
        +--ro test-session*
                [sender-ip sender-udp-port reflector-ip \
                 reflector-udp-port]
           +--ro sid?                                string
           +--ro sender-ip                           inet:ip-address
           +--ro sender-udp-port
           |       dynamic-port-number
           +--ro reflector-ip                        inet:ip-address
           +--ro reflector-udp-port                  inet:port-number
           +--ro parent-connection-client-ip?        inet:ip-address
           +--ro parent-connection-client-tcp-port?  inet:port-number
           +--ro parent-connection-server-ip?        inet:ip-address
           +--ro parent-connection-server-tcp-port?  inet:port-number
           +--ro test-packet-dscp?                   inet:dscp
           +--ro sent-packets?                       uint32
           +--ro rcv-packets?                        uint32
           +--ro last-sent-seq?                      uint32
           +--ro last-rcv-seq?                       uint32
Figure 7: YANG Tree Diagram

5.2. YANG Module

This section presents the YANG module for the TWAMP data model defined in this document. The module imports definitions from "Common YANG Data Types" [RFC6991] and references "Framework for IP Performance Metrics" [RFC2330], "Network performance measurement with periodic streams" [RFC3432], "A One-way Active Measurement Protocol (OWAMP)" [RFC4656], "A Two-Way Active Measurement Protocol (TWAMP)" [RFC5357], "Mixed Security Mode for the Two-Way Active Measurement Protocol (TWAMP)" [RFC5618], "Network Time Protocol Version 4: Protocol and Algorithms Specification" [RFC5905], "Individual Session Control Feature for the Two-Way Active Measurement Protocol (TWAMP)" [RFC5938], "Two-Way Active Measurement Protocol (TWAMP) Reflect Octets and Symmetrical Size Features" [RFC6038], "Advanced Stream and Sampling Framework for IP Performance Metrics (IPPM)" [RFC7312], "IKEv2-Derived Shared Secret Key for the One-Way Active Measurement Protocol (OWAMP) and Two-Way Active Measurement Protocol (TWAMP)" [RFC7717], "Well-Known Port Assignments for the One-Way Active Measurement Protocol (OWAMP) and the Two-Way Active Measurement Protocol (TWAMP)" [RFC8545], and "Registry for Performance Metrics" [RFC8911].

<CODE BEGINS> file "[email protected]"


module ietf-twamp {
  yang-version 1.1;
  namespace "urn:ietf:params:xml:ns:yang:ietf-twamp";
  prefix ietf-twamp;

  import ietf-inet-types {
    prefix inet;
    reference
      "RFC 6991: Common YANG Data Types";
  }

  organization
    "IETF IPPM (IP Performance Metrics) Working Group";
  contact
    "WG Web: <https://datatracker.ietf.org/wg/ippm/documents/>
     WG List: <mailto:[email protected]>

     Editor: Ruth Civil
             <mailto:[email protected]>

     Editor: Al Morton
             <mailto:[email protected]>

     Editor: Reshad Rahman
             <mailto:[email protected]>

     Editor: Mahesh Jethanandani
             <mailto:[email protected]>

     Editor: Kostas Pentikousis
             <mailto:[email protected]>";
  description
    "This YANG module specifies a vendor-independent data
     model for the Two-Way Active Measurement Protocol (TWAMP).

     The data model defines four TWAMP logical entities, namely
     Control-Client, Server, Session-Sender, and Session-Reflector,
     as illustrated in the annotated TWAMP logical model (Figure 1
     of RFC 8913).

     This YANG module uses features to indicate which of the four
     logical entities are supported by a TWAMP implementation.

     The key words 'MUST', 'MUST NOT', 'REQUIRED', 'SHALL', 'SHALL
     NOT', 'SHOULD', 'SHOULD NOT', 'RECOMMENDED', 'NOT RECOMMENDED',
     'MAY', and 'OPTIONAL' in this document are to be interpreted as
     described in BCP 14 (RFC 2119) (RFC 8174) when, and only when,
     they appear in all capitals, as shown here.

     Copyright (c) 2021 IETF Trust and the persons identified as
     authors of the code.  All rights reserved.

     Redistribution and use in source and binary forms, with or
     without modification, is permitted pursuant to, and subject to
     the license terms contained in, the Simplified BSD License set
     forth in Section 4.c of the IETF Trust's Legal Provisions
     Relating to IETF Documents
     (https://trustee.ietf.org/license-info).

     This version of this YANG module is part of RFC 8913; see the
     RFC itself for full legal notices.";

  revision 2021-11-17 {
    description
      "Initial revision.

       References RFC 5357, RFC 5618, RFC 5938, RFC 6038, RFC 7717,
       and RFC 8911.";
    reference
      "RFC 8913: Two-Way Active Measurement Protocol (TWAMP) YANG
       Data Model";
  }

  /*
   * Typedefs
   */

  typedef twamp-modes {
    type bits {
      bit unauthenticated {
        position 0;
        description
          "Unauthenticated mode, in which no encryption or
           authentication is applied in TWAMP-Control and
           TWAMP-Test.  KeyID, Token, and Client-IV are not used in
           the Set-Up-Response message.  See Section 3.1 of
           RFC 4656.";
        reference
          "RFC 4656: A One-way Active Measurement Protocol (OWAMP),
                     Section 3.1";
      }
      bit authenticated {
        position 1;
        description
          "Authenticated mode, in which the Control-Client and
           Server possess a shared secret, thus prohibiting
           'theft of service'.  As per Section 6 of RFC 4656,
           in 'authenticated mode, the timestamp is in the clear
           and is not protected cryptographically in any way,
           while the rest of the message has the same protection
           as in encrypted mode.  This mode allows one to trade off
           cryptographic protection against accuracy of
           timestamps.'";
        reference
          "RFC 4656: A One-way Active Measurement Protocol (OWAMP),
                     Section 6";
      }
      bit encrypted {
        position 2;
        description
          "Encrypted mode 'makes it impossible to alter
           timestamps undetectably' (Section 1 of RFC 4656).
           See also Section 4 of RFC 7717.";
        reference
          "RFC 4656: A One-way Active Measurement Protocol (OWAMP),
                     Section 6
           RFC 7717: IKEv2-Derived Shared Secret Key for the One-Way
           Active Measurement Protocol (OWAMP) and Two-Way Active
           Measurement Protocol (TWAMP), Section 4";
      }
      bit unauth-test-encrypt-control {
        position 3;
        description
          "When using the mixed security mode, the TWAMP-Test
           protocol operates in unauthenticated mode and the
           TWAMP-Control protocol operates in encrypted mode.";
        reference
          "RFC 5618: Mixed Security Mode for the Two-Way Active
           Measurement Protocol (TWAMP)";
      }
      bit individual-session-control {
        position 4;
        description
          "This mode enables individual test sessions using
           Session Identifiers.";
        reference
          "RFC 5938: Individual Session Control Feature
           for the Two-Way Active Measurement Protocol (TWAMP)";
      }
      bit reflect-octets {
        position 5;
        description
          "This mode indicates the reflect octets capability.";
        reference
          "RFC 6038: Two-Way Active Measurement Protocol (TWAMP)
           Reflect Octets and Symmetrical Size Features";
      }
      bit symmetrical-size {
        position 6;
        description
          "This mode indicates support for the symmetrical size
           sender test packet format.";
        reference
          "RFC 6038: Two-Way Active Measurement Protocol (TWAMP)
           Reflect Octets and Symmetrical Size Features";
      }
      bit IKEv2Derived {
        position 7;
        description
          "In this mode, the shared key is derived
           from an Internet Key Exchange Protocol Version 2 (IKEv2)
           security association (SA).";
        reference
          "RFC 7717: IKEv2-Derived Shared Secret Key for
           the One-Way Active Measurement Protocol (OWAMP)
           and Two-Way Active Measurement Protocol (TWAMP)";
      }
    }
    description
      "Specifies the configurable TWAMP-Modes supported during a
       TWAMP-Control connection setup between a Control-Client
       and a Server.  Section 7 of RFC 7717 summarizes the
       'TWAMP-Modes' Registry and points to their
       formal specification.";
  }

  typedef control-client-connection-state {
    type enumeration {
      enum active {
        description
          "Indicates an active TWAMP-Control connection to the
           Server.";
      }
      enum idle {
        description
          "Indicates an idle TWAMP-Control connection to the
           Server.";
      }
    }
    description
      "Indicates the Control-Client TWAMP-Control connection
       state.";
  }

  typedef test-session-state {
    type enumeration {
      enum accepted {
        value 0;
        description
          "Indicates an accepted TWAMP-Test session request.";
      }
      enum failed {
        value 1;
        description
          "Indicates a TWAMP-Test session failure due to
           some unspecified reason (catch-all).";
      }
      enum internal-error {
        value 2;
        description
          "Indicates a TWAMP-Test session failure due to
           an internal error.";
      }
      enum not-supported {
        value 3;
        description
          "Indicates a TWAMP-Test session failure because
           some aspect of the TWAMP-Test session request
           is not supported.";
      }
      enum permanent-resource-limit {
        value 4;
        description
          "Indicates a TWAMP-Test session failure due to
           permanent resource limitations.";
      }
      enum temp-resource-limit {
        value 5;
        description
          "Indicates a TWAMP-Test session failure due to
           temporary resource limitations.";
      }
    }
    description
      "Indicates the Control-Client TWAMP-Test session state.";
  }

  typedef server-ctrl-connection-state {
    type enumeration {
      enum active {
        description
          "Indicates an active TWAMP-Control connection
           to the Control-Client.";
      }
      enum servwait {
        description
          "Indicates that the TWAMP-Control connection to the
           Control-Client is in SERVWAIT as per the definition in
           Section 3.1 of RFC 5357.";
        reference
          "RFC 5357: A Two-Way Active Measurement Protocol (TWAMP),
                     Section 3.1";
      }
    }
    description
      "Indicates the Server TWAMP-Control connection state.";
  }

  typedef sender-session-state {
    type enumeration {
      enum active {
        description
          "Indicates that the TWAMP-Test session is active.";
      }
      enum failure {
        description
          "Indicates that the TWAMP-Test session has failed.";
      }
    }
    description
      "Indicates the Session-Sender TWAMP-Test session state.";
  }

  typedef padding-fill-mode {
    type enumeration {
      enum zero {
        description
          "TWAMP-Test packets are padded with all zeros.";
      }
      enum random {
        description
          "TWAMP-Test packets are padded with pseudorandom
           numbers.";
      }
    }
    description
      "Indicates what type of packet padding is used in the
       TWAMP-Test packets.";
  }

  typedef dynamic-port-number {
    type inet:port-number {
      range "49152..65535";
    }
    description
      "Dynamic range for port numbers.";
  }

  /*
   * Features
   */

  feature control-client {
    description
      "Indicates that the device supports configuration of the
       TWAMP Control-Client logical entity.";
  }

  feature server {
    description
      "Indicates that the device supports configuration of the
       TWAMP Server logical entity.";
  }

  feature session-sender {
    description
      "Indicates that the device supports configuration of the
       TWAMP Session-Sender logical entity.";
  }

  feature session-reflector {
    description
      "Indicates that the device supports configuration of the
       TWAMP Session-Reflector logical entity.";
  }

  /*
   * Reusable node groups
   */

  grouping key-management {
    list key-chain {
      key "key-id";
      leaf key-id {
        type string {
          length "1..80";
        }
        description
          "KeyID used for a TWAMP-Control connection.  As per
           Section 3.1 of RFC 4656, KeyID is 'a UTF-8 string, up to
           80 octets in length' and is used to select which 'shared
           secret the client' (Control-Client) 'wishes to use to
           authenticate or encrypt'.";
      }
      leaf secret-key {
        type binary;
        description
          "The secret key corresponding to the KeyID for this
           TWAMP-Control connection.";
      }
      description
        "Relates KeyIDs with their respective secret keys
         in a TWAMP-Control connection.";
    }
    description
      "Used by the Control-Client and Server for TWAMP-Control
       key management.";
  }

  grouping maintenance-statistics {
    leaf sent-packets {
      type uint32;
      config false;
      description
        "Indicates the number of packets sent.";
    }
    leaf rcv-packets {
      type uint32;
      config false;
      description
        "Indicates the number of packets received.";
    }
    leaf last-sent-seq {
      type uint32;
      config false;
      description
        "Indicates the last sent sequence number.";
    }
    leaf last-rcv-seq {
      type uint32;
      config false;
      description
        "Indicates the last received sequence number.";
    }
    description
      "Used for TWAMP-Test maintenance statistics.";
  }

  grouping count {
    leaf count {
      type uint8 {
        range "10..31";
      }
      default "15";
      description
        "Parameter communicated to the Control-Client as part of
         the Server Greeting message and used for deriving a key
         from a shared secret as per Section 3.1 of RFC 4656:
         MUST be a power of 2 and at least 1024.  It is configured
         by providing said power.  For example, configuring 20 here
         means count 2^20 = 1048576.  The default is 15,
         meaning 2^15 = 32768.";
    }
    description
      "Reusable data structure for count, which is used in both the
       Server and the Control-Client.";
  }

  grouping max-count-exponent {
    leaf max-count-exponent {
      type uint8 {
        range "10..31";
      }
      default "20";
      description
        "This parameter limits the maximum Count value, which MUST
         be a power of 2 and at least 1024 as per RFC 5357.  It is
         configured by providing said power.  For example,
         configuring 10 here means max count 2^10 = 1024.
         The default is 20, meaning 2^20 = 1048576.

         A TWAMP Server uses this configured value in the
         Server Greeting message sent to the Control-Client.

         A TWAMP Control-Client uses this configured value to
         prevent denial-of-service (DoS) attacks by closing the
         control connection to the Server if it 'receives a
         Server-Greeting message with Count greater that [sic] its
         maximum configured value', as per Section 6 of RFC 5357.

         Further, note that according to Section 6 of RFC 5357:

         'If an attacking system set the maximum value in Count
         (2**32), then the system under attack would stall for a
         significant period of time while it attempts to generate
         keys.  Therefore, TWAMP-compliant systems SHOULD have a
         configuration control to limit the maximum Count value.
         The default maximum Count value SHOULD be 32768.'

         In the case of this document, the default max-count-exponent
         value SHOULD be 15, which corresponds to a maximum value of
         2**15 or 32768.

         RFC 5357 does not qualify 'significant period' in terms of
         time, but it is clear that this depends on the processing
         capacity available, and operators need to pay attention to
         this security consideration.";
    }
    description
      "Reusable data structure for max-count that is used in both
       the client (Control-Client) container and the server
       container.";
  }

  /*
   * Configuration data nodes
   */

  container twamp {
    description
      "TWAMP logical entity configuration grouping of four models
       that correspond to the four TWAMP logical entities
       Control-Client, Server, Session-Sender, and Session-Reflector
       as illustrated in Figure 1 of RFC 8913.";
    container client {
      if-feature "control-client";
      description
        "Configuration of the TWAMP Control-Client logical entity.";
      leaf admin-state {
        type boolean;
        default "true";
        description
          "Indicates whether the device is allowed to operate as a
           TWAMP Control-Client.";
      }
      list mode-preference-chain {
        key "priority";
        unique "mode";
        leaf priority {
          type uint16;
          description
            "Indicates the Control-Client mode preference priority,
             expressed as a 16-bit unsigned integer.  Values for the
             priority start with zero, the highest priority, and
             decreasing priority value is indicated by every increase
             in value by one.";
        }
        leaf mode {
          type twamp-modes;
          description
            "The supported TWAMP-Modes matching the corresponding
             priority.";
        }
        description
          "Indicates the Control-Client preferred order of use of
           the supported TWAMP-Modes.

           Depending on the modes available in the TWAMP Server
           Greeting message (see Figure 2 of RFC 7717), the
           Control-Client MUST choose the highest-priority
           mode from the configured mode-preference-chain list.";
      }
      uses key-management;
      list ctrl-connection {
        key "name";
        description
          "List of TWAMP Control-Client control connections.
           Each item in the list describes a control connection
           that will be initiated by this Control-Client.";
        leaf name {
          type string;
          description
            "A unique name used as a key to identify this
             individual TWAMP-Control connection on the
             Control-Client device.";
        }
        leaf client-ip {
          type inet:ip-address;
          description
            "The IP address of the local Control-Client device,
             to be placed in the source IP address field of the
             IP header in TWAMP-Control (TCP) packets belonging
             to this control connection.  If not configured, the
             device SHALL choose its own source IP address.";
        }
        leaf server-ip {
          type inet:ip-address;
          mandatory true;
          description
            "The IP address of the remote Server device to which
             the TWAMP-Control connection will be initiated.";
        }
        leaf server-tcp-port {
          type inet:port-number;
          default "862";
          description
            "This parameter defines the TCP port number that is
             to be used by this outgoing TWAMP-Control connection.
             Typically, this is the well-known TWAMP-Control
             port number (862) as per RFC 5357.  However, there are
             known realizations of TWAMP in the field that were
             implemented before this well-known port number was
             allocated.  These early implementations allowed the
             port number to be configured.  This parameter is
             therefore provided for backward-compatibility
             reasons.";
        }
        leaf control-packet-dscp {
          type inet:dscp;
          default "0";
          description
            "The Differentiated Services Code Point (DSCP) value
             to be placed in the IP header of TWAMP-Control (TCP)
             packets generated by this Control-Client.";
        }
        leaf key-id {
          type string {
            length "1..80";
          }
          description
            "Indicates the KeyID value selected for this
             TWAMP-Control connection.";
        }
        uses max-count-exponent;
        leaf client-tcp-port {
          type inet:port-number;
          config false;
          description
            "Indicates the source TCP port number used in the
             TWAMP-Control packets belonging to this control
             connection.";
        }
        leaf server-start-time {
          type uint64;
          config false;
          description
            "Indicates the Start-Time advertised by the Server in
             the Server-Start message (RFC 4656, Section 3.1),
             representing the time when the current
             instantiation of the Server started operating.
             The timestamp format follows RFC 5905, according to
             Section 4.1.2 of RFC 4656.";
          reference
            "RFC 4656: A One-way Active Measurement Protocol (OWAMP),
             Sections 3.1 and 4.1.2
             RFC 5905: Network Time Protocol Version 4: Protocol and
             Algorithms Specification";
        }
        leaf repeat-count {
          type uint64;
          config false;
          description
            "Indicates how many times the test session has been
             repeated.  When a test is running, this value will be
             greater than 0.  If the repeat parameter is non-zero,
             this value is smaller than or equal to the repeat
             parameter.";
        }
        leaf state {
          type control-client-connection-state;
          config false;
          description
            "Indicates the current TWAMP-Control connection state.";
        }
        leaf selected-mode {
          type twamp-modes;
          config false;
          description
            "The TWAMP-Modes that the Control-Client has chosen for
             this control connection as set in the Mode field of
             the Set-Up-Response message.";
          reference
            "RFC 4656: A One-way Active Measurement Protocol (OWAMP),
                       Section 3.1";
        }
        leaf token {
          type binary {
            length "64";
          }
          config false;
          description
            "This parameter holds the 64 octets containing the
             concatenation of a 16-octet Challenge, a 16-octet AES
             Session-key used for encryption, and a 32-octet
             HMAC-SHA1 Session-key used for authentication; see
             also the last paragraph of Section 6.10 of RFC 4656.

             If the mode defined in RFC 7717 is selected
             (selected-mode), Token is limited to 16 octets.";
          reference
            "RFC 4656: A One-way Active Measurement Protocol (OWAMP),
                       Section 6.10
             RFC 7717: IKEv2-Derived Shared Secret Key for the
             One-Way Active Measurement Protocol (OWAMP) and
             Two-Way Active Measurement Protocol (TWAMP)";
        }
        leaf client-iv {
          type binary {
            length "16";
          }
          config false;
          description
            "Indicates the Control-Client Initialization Vector
             (Client-IV), which is generated randomly by the
             Control-Client.  As per RFC 4656:

             'Client-IV merely needs to be unique (i.e., it MUST
             never be repeated for different sessions using the
             same secret key; a simple way to achieve that without
             the use of cumbersome state is to generate the
             Client-IV values using a cryptographically secure
             pseudo-random number source.'

             If the mode defined in RFC 7717 is selected
             (selected-mode), Client-IV is limited to 12 octets.";
          reference
            "RFC 4656: A One-way Active Measurement Protocol (OWAMP)
             RFC 7717: IKEv2-Derived Shared Secret Key for the
             One-Way Active Measurement Protocol (OWAMP) and
             Two-Way Active Measurement Protocol (TWAMP)";
        }
        list test-session-request {
          key "name";
          description
            "Information associated with the Control-Client
             for this test session.";
          leaf name {
            type string;
            description
              "A unique name to be used for identification of
               this TWAMP-Test session on the Control-Client.";
          }
          leaf sender-ip {
            type inet:ip-address;
            description
              "The IP address of the Session-Sender device,
               which is to be placed in the source IP address
               field of the IP header in TWAMP-Test (UDP) packets
               belonging to this test session.  This value will be
               used to populate the Sender Address field of the
               Request-TW-Session message.

               If not configured, the device SHALL choose its own
               source IP address.";
          }
          leaf sender-udp-port {
            type union {
              type dynamic-port-number;
              type enumeration {
                enum autoallocate {
                  description
                    "Indicates that the Control-Client will
                     auto-allocate the TWAMP-Test (UDP) port number
                     from the dynamic port range.";
                }
              }
            }
            default "autoallocate";
            description
              "The UDP port number that is to be used by
               the Session-Sender for this TWAMP-Test session.
               The number is restricted to the dynamic port range.

               By default, the Control-Client SHALL auto-allocate a
               UDP port number for this TWAMP-Test session.

               The configured (or auto-allocated) value is
               advertised in the Sender Port field of the
               Request-TW-Session message (see Section 3.5 of
               RFC 5357).  Note that in the scenario where a device
               auto-allocates a UDP port number for a session and
               the repeat parameter for that session indicates that
               it should be repeated, the device is free to
               auto-allocate a different UDP port number when it
               negotiates the next (repeated) iteration of this
               session.";
          }
          leaf reflector-ip {
            type inet:ip-address;
            mandatory true;
            description
              "The IP address belonging to the remote
               Session-Reflector device to which the TWAMP-Test
               session will be initiated.  This value will be
               used to populate the Receiver Address field of
               the Request-TW-Session message.";
          }
          leaf reflector-udp-port {
            type inet:port-number {
              range "862 | 49152..65535";
            }
            description
              "This parameter defines the UDP port number that
               will be used by the Session-Reflector for
               this TWAMP-Test session.  The default number is
               within the dynamic port range and is to be placed
               in the Receiver Port field of the Request-TW-Session
               message.  The well-known port (862) MAY be used.";
            reference
              "RFC 8545: Well-Known Port Assignments for the One-Way
               Active Measurement Protocol (OWAMP) and the Two-Way
               Active Measurement Protocol (TWAMP)";
          }
          leaf timeout {
            type uint64;
            units "seconds";
            default "2";
            description
              "The length of time (in seconds) that the
               Session-Reflector should continue to respond to
               packets belonging to this TWAMP-Test session after
               a Stop-Sessions TWAMP-Control message has been
               received.

               This value will be placed in the Timeout field of
               the Request-TW-Session message.";
            reference
              "RFC 5357: A Two-Way Active Measurement Protocol
               (TWAMP), Section 3.5";
          }
          leaf padding-length {
            type uint32 {
              range "64..4096";
            }
            description
              "The number of padding bytes to be added to the
               TWAMP-Test (UDP) packets generated by the
               Session-Sender.

               This value will be placed in the Padding Length
               field of the Request-TW-Session message.";
            reference
              "RFC 4656: A One-way Active Measurement Protocol
               (OWAMP), Section 3.5";
          }
          leaf test-packet-dscp {
            type inet:dscp;
            default "0";
            description
              "The DSCP value to be placed in the IP header
               of TWAMP-Test packets generated by the
               Session-Sender and in the UDP header of the
               TWAMP-Test response packets generated by the
               Session-Reflector for this test session.

               This value will be placed in the Type-P Descriptor
               field of the Request-TW-Session message.";
            reference
              "RFC 5357: A Two-Way Active Measurement Protocol
               (TWAMP)";
          }
          leaf start-time {
            type uint64;
            default "0";
            description
              "Time when the session is to be started
               (but not before the TWAMP Start-Sessions command
               is issued; see Section 3.4 of RFC 5357).

               The start-time value is placed in the Start Time
               field of the Request-TW-Session message.

               The timestamp format follows RFC 5905 as per
               Section 3.5 of RFC 4656.

               The default value of 0 indicates that the session
               will be started as soon as the Start-Sessions
               message is received.";
          }
          leaf repeat {
            type uint32 {
              range "0..4294967295";
            }
            default "0";
            description
              "This value determines if the TWAMP-Test session must
               be repeated.  When a test session has completed, the
               repeat parameter is checked.

               The default value of 0 indicates that the session
               MUST NOT be repeated.

               If the repeat value is 1 through 4,294,967,294,
               then the test session SHALL be repeated using the
               information in the repeat-interval parameter, and the
               parent TWAMP-Control connection for this test
               session is restarted to negotiate a new instance
               of this TWAMP-Test session.

               A value of 4,294,967,295 indicates that the test
               session SHALL be repeated *forever* using the
               information in the repeat-interval parameter and
               SHALL NOT decrement the value.";
          }
          leaf repeat-interval {
            when "../repeat!='0'" {
              description
                "This parameter determines the timing of repeated
                 TWAMP-Test sessions when repeat is more than 0.

                 When the value of repeat-interval is 0, the
                 negotiation of a new test session SHALL begin
                 immediately after the previous test session
                 completes.  Otherwise, the Control-Client will
                 wait for the number of seconds specified in the
                 repeat-interval parameter before negotiating the
                 new instance of this TWAMP-Test session.";
            }
            type uint32;
            units "seconds";
            default "0";
            description
              "Repeat interval (in seconds).";
          }
          list pm-reg-list {
            key "pm-index";
            leaf pm-index {
              type uint16;
              description
                "Numerical index value of a Registered Metric in
                 the Performance Metrics Registry (see RFC 8911).
                 Output statistics are specified in the
                 corresponding Registry Entry.";
            }
            description
              "A list of one or more Performance Metrics Registry
               Index values, which communicate packet stream
               characteristics along with one or more metrics
               to be measured.

               All members of the pm-reg-list MUST have the same
               stream characteristics, such that they combine
               to specify all metrics that shall be measured on
               a single stream.";
            reference
              "RFC 8911: Registry for Performance Metrics";
          }
          leaf state {
            type test-session-state;
            config false;
            description
              "Indicates the TWAMP-Test session state -- an accepted
               request or an indication of an error.";
            reference
              "RFC 5357: A Two-Way Active Measurement Protocol
               (TWAMP), Section 3.5";
          }
          leaf sid {
            type string;
            config false;
            description
              "The Session Identifier (SID) allocated by the Server
               for this TWAMP-Test session and communicated back to
               the Control-Client in the SID field of the
               Accept-Session message.";
            reference
              "RFC 6038: Two-Way Active Measurement Protocol (TWAMP)
               Reflect Octets and Symmetrical Size
               Features, Section 4.3";
          }
        }
      }
    }
    container server {
      if-feature "server";
      description
        "Configuration of the TWAMP Server logical entity.";
      leaf admin-state {
        type boolean;
        default "true";
        description
          "Indicates whether the device is allowed to operate
           as a TWAMP Server.";
      }
      leaf server-tcp-port {
        type inet:port-number;
        default "862";
        description
          "This parameter defines the well-known TCP port number
           that is used by TWAMP-Control.  The Server will listen
           on this port number for incoming TWAMP-Control
           connections.  Although this is defined as a fixed value
           (862) in RFC 5357, there are several realizations of
           TWAMP in the field that were implemented before this
           well-known port number was allocated.  These early
           implementations allowed the port number to be
           configured.  This parameter is therefore provided for
           backward-compatibility reasons.";
      }
      leaf servwait {
        type uint32 {
          range "1..604800";
        }
        units "seconds";
        default "900";
        description
          "TWAMP-Control (TCP) session timeout, in seconds.
           According to Section 3.1 of RFC 5357:

           'The Server MAY discontinue any established control
           connection when no packet associated with that
           connection has been received within SERVWAIT seconds.'";
      }
      leaf control-packet-dscp {
        type inet:dscp;
        description
          "The DSCP value to be placed in the IP header of
           TWAMP-Control (TCP) packets generated by the Server.

           Section 3.1 of RFC 5357 specifies that the Server
           SHOULD use the DSCP value from the Control-Client's
           TCP SYN.  However, for practical purposes, TWAMP will
           typically be implemented using a general-purpose TCP
           stack provided by the underlying operating system,
           and such a stack may not provide this information to the
           user.  Consequently, it is not always possible to
           implement the behavior described in RFC 5357 in an
           OS-portable version of TWAMP.

           The default behavior if this item is not set is to use
           the DSCP value from the Control-Client's TCP SYN.";
        reference
          "RFC 5357: A Two-Way Active Measurement Protocol (TWAMP),
           Section 3.1";
      }
      uses count;
      uses max-count-exponent;
      leaf modes {
        type twamp-modes;
        description
          "The bit mask of TWAMP-Modes this Server instance is
           willing to support; see the IANA 'TWAMP-Modes' Registry.";
      }
      uses key-management;
      list ctrl-connection {
        key "client-ip client-tcp-port server-ip server-tcp-port";
        config false;
        description
          "List of all incoming TWAMP-Control (TCP) connections.";
        leaf client-ip {
          type inet:ip-address;
          description
            "The IP address on the remote Control-Client device,
             which is the source IP address used in the
             TWAMP-Control (TCP) packets belonging to this control
             connection.";
        }
        leaf client-tcp-port {
          type inet:port-number;
          description
            "The source TCP port number used in the TWAMP-Control
             (TCP) packets belonging to this control connection.";
        }
        leaf server-ip {
          type inet:ip-address;
          description
            "The IP address of the local Server device, which is
             the destination IP address used in the
             TWAMP-Control (TCP) packets belonging to this control
             connection.";
        }
        leaf server-tcp-port {
          type inet:port-number;
          description
            "The destination TCP port number used in the
             TWAMP-Control (TCP) packets belonging to this
             control connection.  This will usually be the
             same value as the server-tcp-port configured
             under twamp/server.  However, in the event that
             the user reconfigured server/server-tcp-port
             after this control connection was initiated, this
             value will indicate the server-tcp-port that is
             actually in use for this control connection.";
        }
        leaf state {
          type server-ctrl-connection-state;
          description
            "Indicates the Server TWAMP-Control connection state.";
        }
        leaf control-packet-dscp {
          type inet:dscp;
          description
            "The DSCP value used in the IP header of the
             TWAMP-Control (TCP) packets sent by the Server
             for this control connection.  This will usually
             be the same value as is configured in the
             control-packet-dscp parameter under the twamp/server
             container.  However, in the event that the user
             reconfigures server/dscp after this control
             connection is already in progress, this read-only
             value will show the actual DSCP value in use by this
             TWAMP-Control connection.";
        }
        leaf selected-mode {
          type twamp-modes;
          description
            "The mode that was chosen for this TWAMP-Control
             connection as set in the Mode field of the
             Set-Up-Response message.";
        }
        leaf key-id {
          type string {
            length "1..80";
          }
          description
            "The KeyID value that is in use by this TWAMP-Control
             connection as selected by the Control-Client.";
        }
        uses count {
          description
            "The Count value that is in use by this TWAMP-Control
             connection.  This will usually be the same value
             as is configured under twamp/server.  However, in the
             event that the user reconfigures server/count
             after this control connection is already in progress,
             this read-only value will show the actual count that
             is in use for this TWAMP-Control connection.";
        }
        uses max-count-exponent {
          description
            "This read-only value indicates the actual max-count in
             use for this control connection.  Usually, this would be
             the same value as is configured under twamp/server.";
        }
        leaf salt {
          type binary {
            length "16";
          }
          description
            "A parameter used in deriving a key from a
             shared secret, as described in Section 3.1 of RFC 4656.
             It is communicated to the Control-Client as part of
             the Server Greeting message.";
        }
        leaf server-iv {
          type binary {
            length "16";
          }
          description
            "The Server Initialization Vector (Server-IV)
             generated randomly by the Server.";
        }
        leaf challenge {
          type binary {
            length "16";
          }
          description
            "A random sequence of octets generated by the Server.
             As described in client/token, a Challenge is used
             by the Control-Client to prove possession of a
             shared secret.";
        }
      }
    }
    container session-sender {
      if-feature "session-sender";
      description
        "Configuration of the TWAMP Session-Sender logical entity.";
      leaf admin-state {
        type boolean;
        default "true";
        description
          "Indicates whether the device is allowed to operate
           as a TWAMP Session-Sender.";
      }
      list test-session {
        key "name";
        description
          "List of TWAMP Session-Sender test sessions.";
        leaf name {
          type string;
          description
            "A unique name for this TWAMP-Test session to be used
             for identifying this test session by the
             Session-Sender logical entity.";
        }
        leaf ctrl-connection-name {
          type string;
          config false;
          description
            "The name of the parent TWAMP-Control connection that
             is responsible for negotiating this TWAMP-Test
             session.";
        }
        leaf fill-mode {
          type padding-fill-mode;
          default "zero";
          description
            "Indicates whether the padding added to the
             TWAMP-Test (UDP) packets (1) will contain pseudorandom
             numbers or (2) should consist of all zeros, as per
             Section 4.2.1 of RFC 5357.";
        }
        leaf number-of-packets {
          type uint32;
          mandatory true;
          description
            "The overall number of TWAMP-Test (UDP) packets to be
             transmitted by the Session-Sender for this test
             session.";
        }
        choice packet-distribution {
          description
            "Indicates the distribution to be used for transmitting
             the TWAMP-Test (UDP) packets.";
          case periodic {
            leaf periodic-interval {
              type decimal64 {
                fraction-digits 5;
              }
              units "seconds";
              mandatory true;
              description
                "Indicates the time to wait (in seconds) between
                 the first bits of TWAMP-Test (UDP) packet
                 transmissions for this test session.";
              reference
                "RFC 3432: Network performance measurement with
                 periodic streams";
            }
          }
          case poisson {
            leaf lambda {
              type decimal64 {
                fraction-digits 5;
              }
              units "seconds";
              mandatory true;
              description
                "Indicates the average time interval (in seconds)
                 between packets in the Poisson distribution.
                 The packet is calculated using the reciprocal of
                 lambda and the TWAMP-Test packet size (which
                 depends on the selected mode and the packet
                 padding).";
              reference
                "RFC 2330: Framework for IP Performance Metrics";
            }
            leaf max-interval {
              type decimal64 {
                fraction-digits 5;
              }
              units "seconds";
              description
                "Indicates the maximum time (in seconds)
                 between packet transmissions.";
              reference
                "RFC 7312: Advanced Stream and Sampling Framework
                 for IP Performance Metrics (IPPM)";
            }
          }
        }
        leaf state {
          type sender-session-state;
          config false;
          description
            "Indicates the Session-Sender test session state.";
        }
        uses maintenance-statistics;
      }
    }
    container session-reflector {
      if-feature "session-reflector";
      description
        "Configuration of the TWAMP Session-Reflector logical
         entity.";
      leaf admin-state {
        type boolean;
        default "true";
        description
          "Indicates whether the device is allowed to operate
           as a TWAMP Session-Reflector.";
      }
      leaf refwait {
        type uint32 {
          range "1..604800";
        }
        units "seconds";
        default "900";
        description
          "The Session-Reflector MAY discontinue any session that
           has been started when no packet associated with that
           session has been received for REFWAIT seconds.  As per
           Section 3.1 of RFC 5357, this timeout allows a
           Session-Reflector to free up resources in case of
           failure.";
      }
      list test-session {
        key "sender-ip sender-udp-port
             reflector-ip reflector-udp-port";
        config false;
        description
          "TWAMP Session-Reflector test sessions.";
        leaf sid {
          type string;
          description
            "An auto-allocated identifier for this TWAMP-Test
             session that is unique within the context of this
             Server/Session-Reflector device only.  This value
             is communicated to the Control-Client that
             requested the test session in the SID field of the
             Accept-Session message.";
        }
        leaf sender-ip {
          type inet:ip-address;
          description
            "The IP address on the remote device, which is the
             source IP address used in the TWAMP-Test (UDP) packets
             belonging to this test session.";
        }
        leaf sender-udp-port {
          type dynamic-port-number;
          description
            "The source UDP port used in the TWAMP-Test packets
             belonging to this test session.";
        }
        leaf reflector-ip {
          type inet:ip-address;
          description
            "The IP address of the local Session-Reflector
             device, which is the destination IP address used
             in the TWAMP-Test (UDP) packets belonging to this test
             session.";
        }
        leaf reflector-udp-port {
          type inet:port-number {
            range "862 | 49152..65535";
          }
          description
            "The destination UDP port number used in the
             TWAMP-Test (UDP) test packets belonging to this
             test session.";
        }
        leaf parent-connection-client-ip {
          type inet:ip-address;
          description
            "The IP address on the Control-Client device, which
             is the source IP address used in the TWAMP-Control
             (TCP) packets belonging to the parent control
             connection that negotiated this test session.";
        }
        leaf parent-connection-client-tcp-port {
          type inet:port-number;
          description
            "The source TCP port number used in the TWAMP-Control
             (TCP) packets belonging to the parent control
             connection that negotiated this test session.";
        }
        leaf parent-connection-server-ip {
          type inet:ip-address;
          description
            "The IP address of the Server device, which is the
             destination IP address used in the TWAMP-Control
             (TCP) packets belonging to the parent control
             connection that negotiated this test session.";
        }
        leaf parent-connection-server-tcp-port {
          type inet:port-number;
          description
            "The destination TCP port number used in the
             TWAMP-Control (TCP) packets belonging to the parent
             control connection that negotiated this test
             session.";
        }
        leaf test-packet-dscp {
          type inet:dscp;
          description
            "The DSCP value present in the IP header of
             TWAMP-Test (UDP) packets belonging to this session.";
        }
        uses maintenance-statistics;
      }
    }
  }
}
<CODE ENDS>

6. Data Model Examples

This section presents simple but complete examples of configuring all four entities in Figure 1, based on the YANG module specified in Section 5. The examples are illustrative in nature but aim to be self-contained, i.e., were they to be executed in a real TWAMP implementation, they would lead to correctly configured test sessions. For completeness, examples are provided for both IPv4 and IPv6. The examples are shown using XML [W3C.REC-xml-20081126].

More elaborate examples, which also include authentication parameters, are provided in Appendix A.

6.1. Control-Client

Figure 8 shows a configuration example for a Control-Client with client/admin-state enabled. In a real implementation following Figure 2, this would permit the initiation of TWAMP-Control connections and TWAMP-Test sessions.

<?xml version="1.0" encoding="utf-8"?>
<config xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
  <twamp xmlns="urn:ietf:params:xml:ns:yang:ietf-twamp">
    <client>
      <admin-state>true</admin-state>
    </client>
  </twamp>
</config>
Figure 8: XML Instance Enabling Control-Client Operation

The following example shows a Control-Client with two instances of client/ctrl-connection -- one called "RouterA" and another called "RouterB". Each TWAMP-Control connection is to a different Server. The control connection named "RouterA" has two test session requests. The TWAMP-Control connection named "RouterB" has no TWAMP-Test session requests.

<?xml version="1.0" encoding="utf-8"?>
<config xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
  <twamp xmlns="urn:ietf:params:xml:ns:yang:ietf-twamp">
    <client>
      <admin-state>true</admin-state>
      <ctrl-connection>
        <name>RouterA</name>
        <client-ip>203.0.113.1</client-ip>
        <server-ip>203.0.113.2</server-ip>
        <test-session-request>
          <name>Test1</name>
          <sender-ip>203.0.113.3</sender-ip>
          <sender-udp-port>54001</sender-udp-port>
          <reflector-ip>203.0.113.4</reflector-ip>
          <reflector-udp-port>50001</reflector-udp-port>
          <start-time>0</start-time>
        </test-session-request>
        <test-session-request>
          <name>Test2</name>
          <sender-ip>203.0.113.1</sender-ip>
          <sender-udp-port>54001</sender-udp-port>
          <reflector-ip>203.0.113.2</reflector-ip>
          <reflector-udp-port>50001</reflector-udp-port>
          <start-time>0</start-time>
        </test-session-request>
      </ctrl-connection>
      <ctrl-connection>
        <name>RouterB</name>
        <client-ip>203.0.113.1</client-ip>
        <server-ip>203.0.113.3</server-ip>
      </ctrl-connection>
    </client>
  </twamp>
</config>
<?xml version="1.0" encoding="utf-8"?>
<config xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
  <twamp xmlns="urn:ietf:params:xml:ns:yang:ietf-twamp">
    <client>
      <admin-state>true</admin-state>
      <ctrl-connection>
        <name>RouterA</name>
        <client-ip>2001:db8:203:0:113::1</client-ip>
        <server-ip>2001:db8:203:0:113::2</server-ip>
        <test-session-request>
          <name>Test1</name>
          <sender-ip>2001:db8:203:1:113::3</sender-ip>
          <sender-udp-port>54000</sender-udp-port>
          <reflector-ip>2001:db8:203:1:113::4</reflector-ip>
          <reflector-udp-port>55000</reflector-udp-port>
          <start-time>0</start-time>
        </test-session-request>
        <test-session-request>
          <name>Test2</name>
          <sender-ip>2001:db8:203:0:113::1</sender-ip>
          <sender-udp-port>54001</sender-udp-port>
          <reflector-ip>2001:db8:203:0:113::2</reflector-ip>
          <reflector-udp-port>55001</reflector-udp-port>
          <start-time>0</start-time>
        </test-session-request>
      </ctrl-connection>
      <ctrl-connection>
        <name>RouterB</name>
        <client-ip>2001:db8:203:0:113::1</client-ip>
        <server-ip>2001:db8:203:0:113::3</server-ip>
      </ctrl-connection>
    </client>
  </twamp>
</config>

6.2. Server

Figure 9 shows a configuration example for a Server with server⁠/admin-state enabled, which permits a device following Figure 2 to respond to TWAMP-Control connections and TWAMP-Test sessions.

<?xml version="1.0" encoding="utf-8"?>
<config xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
  <twamp xmlns="urn:ietf:params:xml:ns:yang:ietf-twamp">
    <server>
      <admin-state>true</admin-state>
    </server>
  </twamp>
</config>
Figure 9: XML Instance Enabling Server Operation

The following example presents a Server with the TWAMP-Control connection corresponding to the control connection name (client⁠/ctrl‑connection/name) "RouterA" presented in Section 6.1.

<?xml version="1.0" encoding="utf-8"?>
<data xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
  <twamp xmlns="urn:ietf:params:xml:ns:yang:ietf-twamp">
    <server>
      <admin-state>true</admin-state>
      <ctrl-connection>
        <client-ip>203.0.113.1</client-ip>
        <client-tcp-port>16341</client-tcp-port>
        <server-ip>203.0.113.2</server-ip>
        <server-tcp-port>862</server-tcp-port>
        <state>active</state>
      </ctrl-connection>
    </server>
  </twamp>
</data>
<?xml version="1.0" encoding="utf-8"?>
<data xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
  <twamp xmlns="urn:ietf:params:xml:ns:yang:ietf-twamp">
    <server>
      <admin-state>true</admin-state>
      <ctrl-connection>
        <client-ip>2001:db8:203:0:113::1</client-ip>
        <client-tcp-port>16341</client-tcp-port>
        <server-ip>2001:db8:203:0:113::2</server-ip>
        <server-tcp-port>862</server-tcp-port>
        <state>active</state>
      </ctrl-connection>
    </server>
  </twamp>
</data>

6.3. Session-Sender

Figure 10 shows a configuration example for a Session-Sender with session-sender/admin-state enabled, which permits a device following Figure 2 to initiate TWAMP-Test sessions.

<?xml version="1.0" encoding="utf-8"?>
<config xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
  <twamp xmlns="urn:ietf:params:xml:ns:yang:ietf-twamp">
    <session-sender>
      <admin-state>true</admin-state>
    </session-sender>
  </twamp>
</config>
Figure 10: XML Instance Enabling Session-Sender Operation

The following configuration example shows a Session-Sender with the two TWAMP-Test sessions presented in Section 6.1.

<?xml version="1.0" encoding="utf-8"?>
<data xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
  <twamp xmlns="urn:ietf:params:xml:ns:yang:ietf-twamp">
    <session-sender>
      <admin-state>true</admin-state>
      <test-session>
        <name>Test1</name>
        <ctrl-connection-name>RouterA</ctrl-connection-name>
        <number-of-packets>900</number-of-packets>
        <periodic-interval>1</periodic-interval>
      </test-session>
      <test-session>
        <name>Test2</name>
        <ctrl-connection-name>RouterA</ctrl-connection-name>
        <number-of-packets>900</number-of-packets>
        <lambda>1</lambda>
        <max-interval>2</max-interval>
      </test-session>
    </session-sender>
  </twamp>
</data>

6.4. Session-Reflector

This configuration example shows a Session-Reflector with session‑reflector/admin-state enabled, which permits a device following Figure 2 to respond to TWAMP-Test sessions.

<?xml version="1.0" encoding="utf-8"?>
<config xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
  <twamp xmlns="urn:ietf:params:xml:ns:yang:ietf-twamp">
    <session-reflector>
      <admin-state>true</admin-state>
    </session-reflector>
  </twamp>
</config>
Figure 11: XML Instance Enabling Session-Reflector Operation

The following example shows the two Session-Reflector TWAMP-Test sessions corresponding to the test sessions presented in Section 6.3.

<?xml version="1.0" encoding="utf-8"?>
<data xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
  <twamp xmlns="urn:ietf:params:xml:ns:yang:ietf-twamp">
    <session-reflector>
      <admin-state>true</admin-state>
      <test-session>
        <sender-ip>203.0.113.3</sender-ip>
        <sender-udp-port>54000</sender-udp-port>
        <reflector-ip>203.0.113.4</reflector-ip>
        <reflector-udp-port>50001</reflector-udp-port>
        <sid>1232</sid>
        <parent-connection-client-ip>203.0.113.1</parent-connection-\
client-ip>
        <parent-connection-client-tcp-port>16341</parent-connection-\
client-tcp-port>
        <parent-connection-server-ip>203.0.113.2</parent-connection-\
server-ip>
        <parent-connection-server-tcp-port>862</parent-connection-se\
rver-tcp-port>
        <sent-packets>2</sent-packets>
        <rcv-packets>2</rcv-packets>
        <last-sent-seq>1</last-sent-seq>
        <last-rcv-seq>1</last-rcv-seq>
      </test-session>
      <test-session>
        <sender-ip>203.0.113.1</sender-ip>
        <sender-udp-port>54001</sender-udp-port>
        <reflector-ip>192.0.2.2</reflector-ip>
        <reflector-udp-port>50001</reflector-udp-port>
        <sid>178943</sid>
        <parent-connection-client-ip>203.0.113.1</parent-connection-\
client-ip>
        <parent-connection-client-tcp-port>16341</parent-connection-\
client-tcp-port>
        <parent-connection-server-ip>203.0.113.2</parent-connection-\
server-ip>
        <parent-connection-server-tcp-port>862</parent-connection-se\
rver-tcp-port>
        <sent-packets>21</sent-packets>
        <rcv-packets>21</rcv-packets>
        <last-sent-seq>20</last-sent-seq>
        <last-rcv-seq>20</last-rcv-seq>
      </test-session>
    </session-reflector>
  </twamp>
</data>
<?xml version="1.0" encoding="utf-8"?>
<data xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
  <twamp xmlns="urn:ietf:params:xml:ns:yang:ietf-twamp">
    <session-reflector>
      <admin-state>true</admin-state>
      <test-session>
        <sender-ip>203.0.113.3</sender-ip>
        <sender-udp-port>54000</sender-udp-port>
        <reflector-ip>203.0.113.4</reflector-ip>
        <reflector-udp-port>54001</reflector-udp-port>
        <sid>1232</sid>
        <parent-connection-client-ip>203.0.113.1</parent-connection-\
client-ip>
        <parent-connection-client-tcp-port>16341</parent-connection-\
client-tcp-port>
        <parent-connection-server-ip>203.0.113.2</parent-connection-\
server-ip>
        <parent-connection-server-tcp-port>862</parent-connection-se\
rver-tcp-port>
        <sent-packets>2</sent-packets>
        <rcv-packets>2</rcv-packets>
        <last-sent-seq>1</last-sent-seq>
        <last-rcv-seq>1</last-rcv-seq>
      </test-session>
      <test-session>
        <sender-ip>203.0.113.1</sender-ip>
        <sender-udp-port>54001</sender-udp-port>
        <reflector-ip>192.0.2.2</reflector-ip>
        <reflector-udp-port>55001</reflector-udp-port>
        <sid>178943</sid>
        <parent-connection-client-ip>203.0.113.1</parent-connection-\
client-ip>
        <parent-connection-client-tcp-port>16341</parent-connection-\
client-tcp-port>
        <parent-connection-server-ip>203.0.113.2</parent-connection-\
server-ip>
        <parent-connection-server-tcp-port>862</parent-connection-se\
rver-tcp-port>
        <sent-packets>21</sent-packets>
        <rcv-packets>21</rcv-packets>
        <last-sent-seq>20</last-sent-seq>
        <last-rcv-seq>20</last-rcv-seq>
      </test-session>
    </session-reflector>
  </twamp>
</data>

7. Security Considerations

Virtually all existing measurement systems using TWAMP [RFC5357] are administered by the same network operator. For example, attacks on the measurement infrastructure could be launched by third parties to commandeer the packet generation capability, corrupt the measurements, or perform other nefarious acts.

The YANG module specified in this document defines a schema for data that is designed to be accessed via network management protocols such as NETCONF [RFC6241] or RESTCONF [RFC8040]. The lowest NETCONF layer is the secure transport layer, and the mandatory-to-implement secure transport is Secure Shell (SSH) [RFC6242]. The lowest RESTCONF layer is HTTPS, and the mandatory-to-implement secure transport is TLS [RFC8446].

The Network Configuration Access Control Model (NACM) [RFC8341] provides the means to restrict access for particular NETCONF or RESTCONF users to a preconfigured subset of all available NETCONF or RESTCONF protocol operations and content.

There are a number of data nodes defined in this YANG module that are writable/creatable/deletable (i.e., config true, which is the default). These data nodes may be considered sensitive or vulnerable in some network environments. Write operations (e.g., edit-config) to these data nodes without proper protection can have a negative effect on network operations. These are the subtrees and data nodes and their sensitivity/vulnerability:

Some of the readable data nodes in this YANG module may be considered sensitive or vulnerable in some network environments. It is thus important to control read access (e.g., via get, get-config, or notification) to these data nodes. This is the subtree and data node and its sensitivity/vulnerability:

The TWAMP YANG data model does not define RPC operations, as detailed in Appendix B, and defers the definition of NETCONF RPC operations to each implementation. These RPC operations, when defined, may be considered sensitive or vulnerable in some network environments. It is thus important to control access to these operations.

8. IANA Considerations

IANA has registered the following URI in the "IETF XML Registry" [RFC3688].

URI:
urn:ietf:params:xml:ns:yang:ietf-twamp
Registrant Contact:
The IESG.
XML:
N/A; the requested URI is an XML namespace.

IANA has registered the following YANG module in the "YANG Module Names" registry [RFC6020].

Name:
ietf-twamp
Namespace:
urn:ietf:params:xml:ns:yang:ietf-twamp
Prefix:
twamp
Reference:
RFC 8913

9. References

9.1. Normative References

[RFC2119]
Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, , <https://www.rfc-editor.org/info/rfc2119>.
[RFC3432]
Raisanen, V., Grotefeld, G., and A. Morton, "Network performance measurement with periodic streams", RFC 3432, DOI 10.17487/RFC3432, , <https://www.rfc-editor.org/info/rfc3432>.
[RFC3688]
Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688, DOI 10.17487/RFC3688, , <https://www.rfc-editor.org/info/rfc3688>.
[RFC4086]
Eastlake 3rd, D., Schiller, J., and S. Crocker, "Randomness Requirements for Security", BCP 106, RFC 4086, DOI 10.17487/RFC4086, , <https://www.rfc-editor.org/info/rfc4086>.
[RFC4656]
Shalunov, S., Teitelbaum, B., Karp, A., Boote, J., and M. Zekauskas, "A One-way Active Measurement Protocol (OWAMP)", RFC 4656, DOI 10.17487/RFC4656, , <https://www.rfc-editor.org/info/rfc4656>.
[RFC5357]
Hedayat, K., Krzanowski, R., Morton, A., Yum, K., and J. Babiarz, "A Two-Way Active Measurement Protocol (TWAMP)", RFC 5357, DOI 10.17487/RFC5357, , <https://www.rfc-editor.org/info/rfc5357>.
[RFC5905]
Mills, D., Martin, J., Ed., Burbank, J., and W. Kasch, "Network Time Protocol Version 4: Protocol and Algorithms Specification", RFC 5905, DOI 10.17487/RFC5905, , <https://www.rfc-editor.org/info/rfc5905>.
[RFC6020]
Bjorklund, M., Ed., "YANG - A Data Modeling Language for the Network Configuration Protocol (NETCONF)", RFC 6020, DOI 10.17487/RFC6020, , <https://www.rfc-editor.org/info/rfc6020>.
[RFC6038]
Morton, A. and L. Ciavattone, "Two-Way Active Measurement Protocol (TWAMP) Reflect Octets and Symmetrical Size Features", RFC 6038, DOI 10.17487/RFC6038, , <https://www.rfc-editor.org/info/rfc6038>.
[RFC6241]
Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed., and A. Bierman, Ed., "Network Configuration Protocol (NETCONF)", RFC 6241, DOI 10.17487/RFC6241, , <https://www.rfc-editor.org/info/rfc6241>.
[RFC6242]
Wasserman, M., "Using the NETCONF Protocol over Secure Shell (SSH)", RFC 6242, DOI 10.17487/RFC6242, , <https://www.rfc-editor.org/info/rfc6242>.
[RFC6991]
Schoenwaelder, J., Ed., "Common YANG Data Types", RFC 6991, DOI 10.17487/RFC6991, , <https://www.rfc-editor.org/info/rfc6991>.
[RFC7717]
Pentikousis, K., Ed., Zhang, E., and Y. Cui, "IKEv2-Derived Shared Secret Key for the One-Way Active Measurement Protocol (OWAMP) and Two-Way Active Measurement Protocol (TWAMP)", RFC 7717, DOI 10.17487/RFC7717, , <https://www.rfc-editor.org/info/rfc7717>.
[RFC7950]
Bjorklund, M., Ed., "The YANG 1.1 Data Modeling Language", RFC 7950, DOI 10.17487/RFC7950, , <https://www.rfc-editor.org/info/rfc7950>.
[RFC8040]
Bierman, A., Bjorklund, M., and K. Watsen, "RESTCONF Protocol", RFC 8040, DOI 10.17487/RFC8040, , <https://www.rfc-editor.org/info/rfc8040>.
[RFC8174]
Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, , <https://www.rfc-editor.org/info/rfc8174>.
[RFC8341]
Bierman, A. and M. Bjorklund, "Network Configuration Access Control Model", STD 91, RFC 8341, DOI 10.17487/RFC8341, , <https://www.rfc-editor.org/info/rfc8341>.
[RFC8446]
Rescorla, E., "The Transport Layer Security (TLS) Protocol Version 1.3", RFC 8446, DOI 10.17487/RFC8446, , <https://www.rfc-editor.org/info/rfc8446>.
[RFC8545]
Morton, A., Ed. and G. Mirsky, Ed., "Well-Known Port Assignments for the One-Way Active Measurement Protocol (OWAMP) and the Two-Way Active Measurement Protocol (TWAMP)", RFC 8545, DOI 10.17487/RFC8545, , <https://www.rfc-editor.org/info/rfc8545>.
[RFC8911]
Bagnulo, M., Claise, B., Eardley, P., Morton, A., and A. Akhter, "Registry for Performance Metrics", RFC 8911, DOI 10.17487/RFC8911, , <https://www.rfc-editor.org/info/rfc8911>.
[UML]
ISO/IEC, "Information technology - Open Distributed Processing - Unified Modeling Language (UML) Version 1.4.2", ISO/IEC 19501:2005, OMG-UML VER 1.3, .
[W3C.REC-xml-20081126]
Bray, T., Paoli, J., Sperberg-McQueen, M., Maler, E., and F. Yergeau, "Extensible Markup Language (XML) 1.0 (Fifth Edition)", World Wide Web Consortium Recommendation REC-xml-20081126, , <https://www.w3.org/TR/2008/REC-xml-20081126>.

9.2. Informative References

[NSC]
John, W., Pentikousis, K., Agapiou, G., Jacob, E., Kind, M., Manzalini, A., Risso, F., Staessens, D., Steinert, R., and C. Meirosu, "Research directions in network service chaining", 2013 IEEE SDN for Future Networks and Services (SDN4FNS), Trento, Italy, DOI 10.1109/SDN4FNS.2013.6702549, , <https://doi.org/10.1109/SDN4FNS.2013.6702549>.
[PERF-METRICS]
IANA, "Performance Metrics", <https://www.iana.org/assignments/performance-metrics>.
[RFC2330]
Paxson, V., Almes, G., Mahdavi, J., and M. Mathis, "Framework for IP Performance Metrics", RFC 2330, DOI 10.17487/RFC2330, , <https://www.rfc-editor.org/info/rfc2330>.
[RFC5618]
Morton, A. and K. Hedayat, "Mixed Security Mode for the Two-Way Active Measurement Protocol (TWAMP)", RFC 5618, DOI 10.17487/RFC5618, , <https://www.rfc-editor.org/info/rfc5618>.
[RFC5938]
Morton, A. and M. Chiba, "Individual Session Control Feature for the Two-Way Active Measurement Protocol (TWAMP)", RFC 5938, DOI 10.17487/RFC5938, , <https://www.rfc-editor.org/info/rfc5938>.
[RFC7312]
Fabini, J. and A. Morton, "Advanced Stream and Sampling Framework for IP Performance Metrics (IPPM)", RFC 7312, DOI 10.17487/RFC7312, , <https://www.rfc-editor.org/info/rfc7312>.
[RFC7426]
Haleplidis, E., Ed., Pentikousis, K., Ed., Denazis, S., Hadi Salim, J., Meyer, D., and O. Koufopavlou, "Software-Defined Networking (SDN): Layers and Architecture Terminology", RFC 7426, DOI 10.17487/RFC7426, , <https://www.rfc-editor.org/info/rfc7426>.
[RFC8018]
Moriarty, K., Ed., Kaliski, B., and A. Rusch, "PKCS #5: Password-Based Cryptography Specification Version 2.1", RFC 8018, DOI 10.17487/RFC8018, , <https://www.rfc-editor.org/info/rfc8018>.
[RFC8340]
Bjorklund, M. and L. Berger, Ed., "YANG Tree Diagrams", BCP 215, RFC 8340, DOI 10.17487/RFC8340, , <https://www.rfc-editor.org/info/rfc8340>.
[RFC8342]
Bjorklund, M., Schoenwaelder, J., Shafer, P., Watsen, K., and R. Wilton, "Network Management Datastore Architecture (NMDA)", RFC 8342, DOI 10.17487/RFC8342, , <https://www.rfc-editor.org/info/rfc8342>.

Appendix A. Detailed Data Model Examples

This appendix extends the examples presented in Section 6 by configuring more fields, such as authentication parameters, DSCP values, and so on.

A.1. Control-Client

<?xml version="1.0" encoding="utf-8"?>
<data xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
  <twamp xmlns="urn:ietf:params:xml:ns:yang:ietf-twamp">
    <client>
      <admin-state>true</admin-state>
      <mode-preference-chain>
        <priority>0</priority>
        <mode>authenticated</mode>
      </mode-preference-chain>
      <mode-preference-chain>
        <priority>1</priority>
        <mode>unauthenticated</mode>
      </mode-preference-chain>
      <key-chain>
        <key-id>KeyClient1ToRouterA</key-id>
        <secret-key>c2VjcmV0MQ==</secret-key>
      </key-chain>
      <key-chain>
        <key-id>KeyForRouterB</key-id>
        <secret-key>c2VjcmV0Mg0K</secret-key>
      </key-chain>
      <ctrl-connection>
        <name>RouterA</name>
        <client-ip>203.0.113.1</client-ip>
        <server-ip>203.0.113.2</server-ip>
        <control-packet-dscp>32</control-packet-dscp>
        <key-id>KeyClient1ToRouterA</key-id>
        <test-session-request>
          <name>Test1</name>
          <sender-ip>203.0.113.3</sender-ip>
          <sender-udp-port>54000</sender-udp-port>
          <reflector-ip>203.0.113.4</reflector-ip>
          <reflector-udp-port>55000</reflector-udp-port>
          <padding-length>64</padding-length>
          <start-time>0</start-time>
        </test-session-request>
        <test-session-request>
          <name>Test2</name>
          <sender-ip>203.0.113.1</sender-ip>
          <sender-udp-port>54001</sender-udp-port>
          <reflector-ip>203.0.113.2</reflector-ip>
          <reflector-udp-port>55001</reflector-udp-port>
          <padding-length>128</padding-length>
          <start-time>0</start-time>
        </test-session-request>
      </ctrl-connection>
    </client>
  </twamp>
</data>
<?xml version="1.0" encoding="utf-8"?>
<data xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
  <twamp xmlns="urn:ietf:params:xml:ns:yang:ietf-twamp">
    <client>
      <admin-state>true</admin-state>
      <mode-preference-chain>
        <priority>0</priority>
        <mode>authenticated</mode>
      </mode-preference-chain>
      <mode-preference-chain>
        <priority>1</priority>
        <mode>unauthenticated</mode>
      </mode-preference-chain>
      <key-chain>
        <key-id>KeyClient1ToRouterA</key-id>
        <secret-key>c2VjcmV0MQ==</secret-key>
      </key-chain>
      <key-chain>
        <key-id>KeyForRouterB</key-id>
        <secret-key>c2VjcmV0Mg0K</secret-key>
      </key-chain>
      <ctrl-connection>
        <name>RouterA</name>
        <client-ip>2001:db8:203:0:113::1</client-ip>
        <server-ip>2001:db8:203:0:113::2</server-ip>
        <control-packet-dscp>32</control-packet-dscp>
        <key-id>KeyClient1ToRouterA</key-id>
        <test-session-request>
          <name>Test1</name>
          <sender-ip>2001:db8:10:1:1::1</sender-ip>
          <sender-udp-port>54000</sender-udp-port>
          <reflector-ip>2001:db8:10:1:1::2</reflector-ip>
          <reflector-udp-port>55000</reflector-udp-port>
          <padding-length>64</padding-length>
          <start-time>0</start-time>
        </test-session-request>
        <test-session-request>
          <name>Test2</name>
          <sender-ip>2001:db8:203:0:113::1</sender-ip>
          <sender-udp-port>54001</sender-udp-port>
          <reflector-ip>2001:db8:203:0:113::2</reflector-ip>
          <reflector-udp-port>55001</reflector-udp-port>
          <padding-length>128</padding-length>
          <start-time>0</start-time>
        </test-session-request>
      </ctrl-connection>
    </client>
  </twamp>
</data>

A.2. Server

<?xml version="1.0" encoding="utf-8"?>
<data xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
  <twamp xmlns="urn:ietf:params:xml:ns:yang:ietf-twamp">
    <server>
      <admin-state>true</admin-state>
      <servwait>1800</servwait>
      <control-packet-dscp>32</control-packet-dscp>
      <modes>authenticated unauthenticated</modes>
      <count>15</count>
      <key-chain>
        <key-id>KeyClient1ToRouterA</key-id>
        <secret-key>c2VjcmV0MQ==</secret-key>
      </key-chain>
      <key-chain>
        <key-id>KeyClient10ToRouterA</key-id>
        <secret-key>c2VjcmV0MTANCg==</secret-key>
      </key-chain>
      <ctrl-connection>
        <client-ip>203.0.113.1</client-ip>
        <client-tcp-port>16341</client-tcp-port>
        <server-ip>203.0.113.2</server-ip>
        <server-tcp-port>862</server-tcp-port>
        <control-packet-dscp>32</control-packet-dscp>
        <selected-mode>unauthenticated</selected-mode>
        <key-id>KeyClient1ToRouterA</key-id>
        <count>15</count>
      </ctrl-connection>
    </server>
  </twamp>
</data>
<?xml version="1.0" encoding="utf-8"?>
<data xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
  <twamp xmlns="urn:ietf:params:xml:ns:yang:ietf-twamp">
    <server>
      <admin-state>true</admin-state>
      <servwait>1800</servwait>
      <control-packet-dscp>32</control-packet-dscp>
      <modes>authenticated unauthenticated</modes>
      <count>15</count>
      <key-chain>
        <key-id>KeyClient1ToRouterA</key-id>
        <secret-key>c2VjcmV0MQ==</secret-key>
      </key-chain>
      <key-chain>
        <key-id>KeyClient10ToRouterA</key-id>
        <secret-key>c2VjcmV0MTANCg==</secret-key>
      </key-chain>
      <ctrl-connection>
        <client-ip>2001:db8:203:0:113::1</client-ip>
        <client-tcp-port>16341</client-tcp-port>
        <server-ip>2001:db8:203:0:113::2</server-ip>
        <server-tcp-port>862</server-tcp-port>
        <control-packet-dscp>32</control-packet-dscp>
        <selected-mode>unauthenticated</selected-mode>
        <key-id>KeyClient1ToRouterA</key-id>
        <count>15</count>
      </ctrl-connection>
    </server>
  </twamp>
</data>

A.3. Session-Sender

<?xml version="1.0" encoding="utf-8"?>
<data xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
  <twamp xmlns="urn:ietf:params:xml:ns:yang:ietf-twamp">
    <session-sender>
      <admin-state>true</admin-state>
      <test-session>
        <name>Test1</name>
        <ctrl-connection-name>RouterA</ctrl-connection-name>
        <fill-mode>zero</fill-mode>
        <number-of-packets>900</number-of-packets>
        <periodic-interval>1</periodic-interval>
        <sent-packets>2</sent-packets>
        <rcv-packets>2</rcv-packets>
        <last-sent-seq>1</last-sent-seq>
        <last-rcv-seq>1</last-rcv-seq>
      </test-session>
      <test-session>
        <name>Test2</name>
        <ctrl-connection-name>RouterA</ctrl-connection-name>
        <fill-mode>random</fill-mode>
        <number-of-packets>900</number-of-packets>
        <lambda>1</lambda>
        <max-interval>2</max-interval>
        <sent-packets>21</sent-packets>
        <rcv-packets>21</rcv-packets>
        <last-sent-seq>20</last-sent-seq>
        <last-rcv-seq>20</last-rcv-seq>
      </test-session>
    </session-sender>
  </twamp>
</data>

A.4. Session-Reflector

<?xml version="1.0" encoding="utf-8"?>
<data xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
  <twamp xmlns="urn:ietf:params:xml:ns:yang:ietf-twamp">
    <session-reflector>
      <admin-state>true</admin-state>
      <test-session>
        <sender-ip>203.0.113.3</sender-ip>
        <sender-udp-port>54000</sender-udp-port>
        <reflector-ip>203.0.113.4</reflector-ip>
        <reflector-udp-port>55000</reflector-udp-port>
        <sid>1232</sid>
        <parent-connection-client-ip>203.0.113.1</parent-connection-\
client-ip>
        <parent-connection-client-tcp-port>16341</parent-connection-\
client-tcp-port>
        <parent-connection-server-ip>203.0.113.2</parent-connection-\
server-ip>
        <parent-connection-server-tcp-port>862</parent-connection-se\
rver-tcp-port>
        <test-packet-dscp>32</test-packet-dscp>
        <sent-packets>2</sent-packets>
        <rcv-packets>2</rcv-packets>
        <last-sent-seq>1</last-sent-seq>
        <last-rcv-seq>1</last-rcv-seq>
      </test-session>
      <test-session>
        <sender-ip>203.0.113.1</sender-ip>
        <sender-udp-port>54001</sender-udp-port>
        <reflector-ip>192.0.2.2</reflector-ip>
        <reflector-udp-port>55001</reflector-udp-port>
        <sid>178943</sid>
        <parent-connection-client-ip>203.0.113.1</parent-connection-\
client-ip>
        <parent-connection-client-tcp-port>16341</parent-connection-\
client-tcp-port>
        <parent-connection-server-ip>203.0.113.2</parent-connection-\
server-ip>
        <parent-connection-server-tcp-port>862</parent-connection-se\
rver-tcp-port>
        <test-packet-dscp>32</test-packet-dscp>
        <sent-packets>21</sent-packets>
        <rcv-packets>21</rcv-packets>
        <last-sent-seq>20</last-sent-seq>
        <last-rcv-seq>20</last-rcv-seq>
      </test-session>
    </session-reflector>
  </twamp>
</data>
<?xml version="1.0" encoding="utf-8"?>
<data xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
  <twamp xmlns="urn:ietf:params:xml:ns:yang:ietf-twamp">
    <session-reflector>
      <admin-state>true</admin-state>
      <test-session>
        <sender-ip>2001:db8:10:1:1::1</sender-ip>
        <sender-udp-port>54000</sender-udp-port>
        <reflector-ip>2001:db8:10:1:1::2</reflector-ip>
        <reflector-udp-port>55000</reflector-udp-port>
        <sid>1232</sid>
        <parent-connection-client-ip>2001:db8:203:0:113::1</parent-c\
onnection-client-ip>
        <parent-connection-client-tcp-port>16341</parent-connection-\
client-tcp-port>
        <parent-connection-server-ip>2001:db8:203:0:113::2</parent-c\
onnection-server-ip>
        <parent-connection-server-tcp-port>862</parent-connection-se\
rver-tcp-port>
        <test-packet-dscp>32</test-packet-dscp>
        <sent-packets>2</sent-packets>
        <rcv-packets>2</rcv-packets>
        <last-sent-seq>1</last-sent-seq>
        <last-rcv-seq>1</last-rcv-seq>
      </test-session>
      <test-session>
        <sender-ip>2001:db8:203:0:113::1</sender-ip>
        <sender-udp-port>54001</sender-udp-port>
        <reflector-ip>2001:db8:192:68::2</reflector-ip>
        <reflector-udp-port>55001</reflector-udp-port>
        <sid>178943</sid>
        <parent-connection-client-ip>2001:db8:203:0:113::1</parent-c\
onnection-client-ip>
        <parent-connection-client-tcp-port>16341</parent-connection-\
client-tcp-port>
        <parent-connection-server-ip>2001:db8:203:0:113::2</parent-c\
onnection-server-ip>
        <parent-connection-server-tcp-port>862</parent-connection-se\
rver-tcp-port>
        <test-packet-dscp>32</test-packet-dscp>
        <sent-packets>21</sent-packets>
        <rcv-packets>21</rcv-packets>
        <last-sent-seq>20</last-sent-seq>
        <last-rcv-seq>20</last-rcv-seq>
      </test-session>
    </session-reflector>
  </twamp>
</data>

Appendix B. TWAMP Operational Commands

TWAMP operational commands could be performed programmatically or manually, e.g., using a command-line interface (CLI).

With respect to programmability, YANG can be used to define NETCONF Remote Procedure Calls (RPCs); therefore, it would be, in principle, possible to define TWAMP RPC operations for actions such as starting or stopping control connections, test sessions, or groups of sessions; retrieving results; clearing stored results; and so on.

However, TWAMP [RFC5357] does not attempt to describe such operational actions. Refer also to Section 2 and the unlabeled links in Figure 1. In actual deployments, different TWAMP implementations may support different sets of operational commands, with different restrictions. Therefore, this document considers it the responsibility of the individual implementation to define its corresponding data model for TWAMP operational commands.

Acknowledgments

We thank Fred Baker, Kevin D'Souza, Gregory Mirsky, Brian Trammell, Robert Sherman, and Marius Georgescu for their thorough and constructive reviews, comments, and text suggestions.

Haoxing Shen contributed to the definition of the YANG module in Section 5.

Jan Lindblad and Ladislav Lhotka did thorough reviews of the YANG module and the examples in Appendix A.

Kostas Pentikousis was partially supported by FP7 UNIFY, a research project partially funded by the European Community under the Seventh Framework Program (grant agreement no. 619609). The views expressed here are those of the authors only. The European Commission is not liable for any use that may be made of the information in this document.

Contributors

Lianshu Zheng

Authors' Addresses

Ruth Civil
Ciena Corporation
307 Legget Drive
Kanata ON K2K 3C8
Canada
Al Morton
AT&T Labs
200 Laurel Avenue South
Middletown, NJ 07748
United States of America
Reshad Rahman
Canada
Mahesh Jethanandani
Xoriant Corporation
1248 Reamwood Avenue
Sunnyvale, CA 94089
United States of America
Kostas Pentikousis (editor)
Detecon
Winterfeldtstrasse 21
10781 Berlin
Germany