Internet-Draft YANG Node Tags July 2023
Wu, et al. Expires 9 January 2024 [Page]
Workgroup:
NETMOD Working Group
Internet-Draft:
draft-ietf-netmod-node-tags-10
Updates:
8407 (if approved)
Published:
Intended Status:
Standards Track
Expires:
Authors:
Q. Wu
Huawei
B. Claise
Huawei
M. Boucadair
Orange
P. Liu
China Mobile
Z. Du
China Mobile

Node Tags in YANG Modules

Abstract

This document defines a method to tag nodes that are associated with the operation and management data in YANG modules. This method for tagging YANG nodes is meant to be used for classifying either data nodes or instances of data nodes from different YANG modules and identifying their characteristic data. Tags may be registered as well as assigned during the definition of the module, assigned by implementations, or dynamically defined and set by users.

This document also provides guidance to future YANG data model writers; as such, this document updates RFC 8407.

Status of This Memo

This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."

This Internet-Draft will expire on 9 January 2024.

Table of Contents

1. Introduction

The use of tags for classification and organization purposes is widespread, not only within IETF protocols, but globally in the Internet (e.g., "#hashtags"). For the specific case of YANG data models, a module tag has already been defined as a string that is associated with a module name at the module level [RFC8819]for YANG modules classification.

Many data models have been specified by various Standards Developing Organizations (SDOs) and the Open Source community, and it is likely that many more will be specified. These models cover many of the networking protocols and techniques. However, data nodes defined by these technology-specific data models might represent only a portion of fault, configuration, accounting, performance, and security (FCAPS) management information ([FCAPS]) at different levels and network locations, but also categorized in various different ways. Furthermore, there is no consistent classification criteria or representations for a specific service, feature, or data source.

This document defines tags for both nodes in the schema tree and instance nodes in the data tree, and shows how these tags can be associated with nodes within a YANG module, to:

To that aim, this document defines a YANG module [RFC7950] that augments the YANG Module Tags ([RFC8819]) to provide a list of node entries to which add node tags or from which to remove node tags, as well as a way to view the set of node tags associated with specific data nodes or instance of data nodes within YANG modules.This new module is: "ietf-node-tags" (Section 7).

Typically, NETCONF clients can discover node tags supported by a NETCONF server by means of the <get-data> operation on the operational datastore (Section 3.1 of [RFC8526]) via the "ietf-node-tags" module. Alternatively, <get-schema> operation [RFC6022] can be used to retrieve tags for nodes in the schema tree in any data module. These node tags can be used by a NETCONF [RFC6241] or RESTCONF [RFC8040] client to classify either data nodes or instance of these data nodes from different YANG modules and identify characteristic data and associated path to the nodes or node instances. Therefore, the NETCONF/ RESTCONF client can query specific configuration or operational state on a server corresponding to characteristic data.

Similar to YANG module tags defined in [RFC8819], these node tags (e.g., tags for node in the schema node) may be registered or assigned during the module definition, assigned (e.g., tags for nodes in the data tree) by implementations, or dynamically defined and set by users. The contents of node tags from the operational state view are constructed using the following steps:

  1. System tags (i.e., tags of "system" origin) that are assigned during the module definition time are added;
  2. User-configured tags (i.e., tags of "intended" origin) that are dynamically defined and added by users at runtime;
  3. Any tag that is equal to a masked-tag is removed.

This document defines an extension statement to indicate tags for data nodes. YANG metadata annotations are also defined in [RFC7952] as a YANG extension. The values of YANG metadata annotation are attached to a given data node instance and decided and assigned by the server and sent to the client (e.g., the origin value indicates to the client the origin of a particular data node instance) while tags for data node in the schema tree defined in Section 6 are retrieved centrally via the "ietf-node-tags" module and can be either assigned during the module defintion time or dynamically set by the client for a given data node instance.

This document also defines an IANA registry for tag prefixes and a set of globally assigned tags (Section 9).

Section 8 provides guidelines for authors of YANG data models. This document updates [RFC8407].

The YANG data model in this document conforms to the Network Management Datastore Architecture defined in [RFC8342].

2. Terminology

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119][RFC8174] when, and only when, they appear in all capitals, as shown here.

The following terms are defined in [RFC7950] and are not redefined here:

This document defines the following term:

Node Tag:
Tag for YANG nodes used for classifying either data nodes or instances of data nodes from different YANG modules and identifying their characteristic data.
Metric:
Metrics are a specific kind of telemetry data. They represent a snapshot of the current state for a set of data. They are distinct from logs or events, which focus on records or information about individual events [OpenMetrics].
Info:
Info is used to expose textual information which SHOULD NOT change during process lifetime. Common examples are an application's version [OpenMetrics].
Gauge:
Gauges are current measurements, such as bytes of memory currently used or the number of items in a queue. For gauges the absolute value is what is of interest to a user [OpenMetrics].
Counter:
Counters measure discrete events. Common examples are the number of HTTP requests received, CPU seconds spent, or bytes sent. For counters how quickly they are increasing over time is what is of interest to a user [OpenMetrics].
Summary:
Summaries measure distributions of discrete events and can be used to measure an average event size [OpenMetrics].
Unknown:
Unknown MAY be used when it is impossible to determine the types of individual metrics from 3rd party systems [OpenMetrics].

The meanings of the symbols in tree diagrams are defined in [RFC8340].

3. Sample Use Cases for Node Tags

The following describes some use cases to illustrate the use of node tags. This section does not intend to be exhaustive.

An example of the use of tags is to search discrete categories of YANG nodes that are scattered across the same or different YANG modules supported by a device. For example, if instances of these nodes in YANG modules are adequately tagged and set by a first client ("Client A") via the "ietf-node-tags" module (Section 7) and retrieved by another client ("Client B") from the operational datastore, then "Client B" can obtain the path to the tagged nodes and subscribe only to network performance related data node instances in the operational datastore supported by a device.

"Client B" can also subscribe to updates from the operational datastore using the "ietf-node-tags" module. Any tag changes in the updates will then resynchronize to the "Client B".

Also, tag classification is useful for users searching data node repositories. A query restricted to the "ietf:counter" data node tag in the "ietf-node-tags" module can be used to return only the YANG nodes that are associated with the counter. Without tags, a user would need to know the name of all the IETF YANG data nodes or instances of data nodes in different YANG modules.

Future management protocol extensions could allow for filtering queries of configuration or operational state on a server based on tags (for example, return all operational state related to system management).

4. Node Tag Values

All node tags (except in some cases of user tags as described in Section 4.3) begin with a prefix indicating who owns their definition. All tag prefixes MUST end with a colon and Colons MUST NOT be used within a prefix. An IANA registry (Section 9.1) is used to register node tag prefixes. Three prefixes are defined in the subsections that follow.

No further structure is imposed by this document on the value following the registered prefix, and the value can contain any YANG type 'string' characters except carriage returns, newlines, tabs, and spaces.

Except for the conflict-avoiding prefix, this document is purposefully not specifying any structure on (i.e., restricting) the tag values. The intent is to avoid arbitrarily restricting the values that designers, implementers, and users can use. As a result of this choice, designers, implementers, and users are free to add or not add any structure they may require to their own tag values.

4.1. IETF Tags

An IETF tag is a node tag that has the prefix "ietf:".

All IETF node tags are registered with IANA in the registry defined in Section 9.2. These IETF Node Tags MUST conform to Net-Unicode as defined in [RFC5198], and SHOULD not need normalization.

4.2. Vendor Tags

A vendor tag is a tag that has the prefix "vendor:".

These tags are defined by the vendor that implements the module, and are not registered with IANA. However, it is RECOMMENDED that the vendor includes extra identification in the tag to avoid collisions, such as using the enterprise or organization name following the "vendor:" prefix (e.g., vendor:entno:vendor-defined-classifier) [RFC9371].

4.3. User Tags

User tags are defined by a user/administrator and are not registered by IANA.

Any tag with the prefix "user:" is a user tag. Furthermore, any tag that does not contain a colon (":", i.e., has no prefix) is also a user tag.

Users are not required to use the "user:" prefix; however, doing so is RECOMMENDED.

4.4. Reserved Tags

Section 9.1 describes the IANA registry of tag prefixes. Any prefix not included in that registry is reserved for future use, but tags starting with such a prefix are still valid tags.

Therefore an implementation SHOULD be able to process all tags regardless of their prefixes.

5. Node Tag Management

Tags may be associated with a data node within a YANG module in a number of ways. Typically, tags may be defined and associated at the module design time, at implementation time without the need of a live server, or via user administrative control. As the main consumers of node tags are users, users may also remove any tag from a live server, no matter how the tag became associated with a data node within a YANG module.

5.1. Module Design Tagging

A data node definition MAY indicate a set of node tags to be added by a module's implementer. These design time tags are indicated using 'node-tag' extension statement.

If the data node is defined in an IETF Standards Track document, node tags MUST be IETF Tags (Section 4.1). Thus, new data nodes can drive the addition of new IETF tags to the IANA registry defined in Section 9.2, and the IANA registry can serve as a check against duplication.

5.2. Implementation Tagging

An implementation that wishes to define additional tags to associate with data nodes within a YANG module MAY do so at implementation time. These tags SHOULD be IETF (i.e., registered)), but MAY be vendor tags. IETF tags allows better interoperability than vendor tags.

5.3. User Tagging

Node tags that are dynamically defined, with or without a prefix, can be added by the user from a server using normal configuration mechanisms.

In order to remove a node tag from the operational datastore, the user adds a matching "masked-tag" entry for a given node within the 'ietf-node-tags' module.

6. Node Tags Module Structure

6.1. Node Tags Module Tree

The tree associated with the "ietf-node-tags" module is shown as figure 1:

module: ietf-node-tags
augment /tags:module-tags/tags:module:
  +--rw node-tags
     +--rw node* [id]
        +--rw id            unit64
        +--rw node-selector nacm:node-instance-identifier
        +--rw tags*         tags:tag
        +--rw masked-tag*   tags:tag
Figure 1: YANG Module Node Tags Tree Diagram

7. Node Tags YANG Module

The "ietf-node-tags" module imports types from [RFC8819] and [RFC8341].

<CODE BEGINS> file "[email protected]"

module ietf-node-tags {
  yang-version 1.1;
  namespace "urn:ietf:params:xml:ns:yang:ietf-node-tags";
  prefix ntags;

  import ietf-netconf-acm {
    prefix nacm;
    reference
    "RFC 8341: Network Configuration Access Control
               Model";
  }
  import ietf-module-tags {
    prefix tags;
    reference
    "RFC 8819: YANG Module Tags";
  }

  organization
    "IETF NetMod Working Group (NetMod)";
  contact
   "WG Web:  <https://datatracker.ietf.org/wg/netmod/>
    WG List: <mailto:[email protected]>

    Editor: Qin Wu
            <mailto:[email protected]>

    Editor: Benoit Claise
            <mailto:[email protected]>

    Editor: Mohamed Boucadair
            <mailto:[email protected]>

    Editor: Peng Liu
            <mailto:[email protected]>

    Editor: Zongpeng Du
            <mailto:[email protected]>";
   // RFC Ed.: replace XXXX with actual RFC number and
   // remove this note.
  description
    "This module describes a mechanism associating
     tags with YANG node within YANG modules. Tags may be IANA
     assigned or privately defined.

     Copyright (c) 2022 IETF Trust and the persons identified as
     authors of the code. All rights reserved.

     Redistribution and use in source and binary forms, with or
     without modification, is permitted pursuant to, and subject
     to the license terms contained in, the Revised BSD License
     set forth in Section 4.c of the IETF Trust's Legal Provisions
     Relating to IETF Documents
     (https://trustee.ietf.org/license-info).

     This version of this YANG module is part of RFC XXXX
     (https://datatracker.ietf.org/html/rfcXXXX); see the RFC
     itself for full legal notices.";

   // RFC Ed.: Update the date below with the date of RFC
   // publication and RFC number and remove this note.
  revision 2022-02-04 {
    description
      "Initial revision.";
    reference
      "RFC XXXX: Node Tags in YANG Modules";
  }
  extension node-tag {
    argument tag;
    description
      "The argument 'tag' is of type 'tag'. This extension statement
       is used by module authors to indicate node tags that should
       be added automatically by the system. As such,  the origin of
       the value for the pre-defined tags should be set to 'system'.";
  }

  augment "/tags:module-tags/tags:module" {
    description
      "Augment the Module Tags module with node tag
       attributes.";
    container node-tags {
      description
        "Contains the list of nodes or node instances and their
         associated node tags.";
      list node {
        key "id";
        description
          "Includes a list of nodes and their associated
           node tags.";
        leaf id   {
          type uint64;
          description
            "Identification of each data node within YANG module. It is
             unique 64-bit unsigned integers.";
        }
        leaf node-selector {
          type nacm:node-instance-identifier;
          description
            "Selects the data nodes for which tags are specified.";
        }
       leaf-list tags {
          type tags:tag;
          description
            "Lists the tags associated with the node within
             the YANG  module.

             See the IANA 'YANG Node Tag Prefixes' registry
             for reserved prefixes and the IANA 'IETF YANG Data
             Node Tags' registry for IETF tags.

             The 'operational' state view of this list is
             constructed using the following steps:

             1) System tags (i.e., tags of 'system' origin) are
                added.
             2) User configured tags (i.e., tags of 'intended'
                origin) are added.
             3) Any tag that is equal to a masked-tag is removed.";
          reference
            "RFC XXXX: node Tags in YANG Data
                       Modules, Section 9";
       }
        leaf-list masked-tag {
          type tags:tag;
          description
            "The list of tags that should not be associated with the
             node within the YANG module. The user can remove (mask)
             tags from the operational state datastore by adding them
             to this list. It is not an error to add tags to this list
             that are not associated with the data node within YANG
             module, but they have no operational effect.";
        }
       }
      }
   }
  }

<CODE ENDS>

8. Guidelines to Model Writers

This section updates [RFC8407] by providing text that may be regarded as a new subsection to Section 4 of that document. It does not change anything already present in [RFC8407].

8.1. Define Standard Tags

A module MAY indicate, using node tag extension statements, a set of node tags that are to be automatically associated with nodes within the module (i.e., not added through configuration).

module example-module-A {
  //...
  import ietf-node-tags { prefix ntags; }

  container top {
    list X {
      leaf foo {
         ntags:node-tag "ietf:metric";
      }
      leaf bar {
        ntags:node-tag "ietf:info";
      }
    }
  }
  // ...
}

The module writer can use existing standard node tags, or use new node tags defined in the data node definition, as appropriate.

For IETF standardized modules, new node tags MUST be assigned in the IANA registry defined in section 9.2 of RFC xxxx.

A data node can contain one or multiple node tags. Not all data nodes need to be tagged. A data node to be tagged with an initial value from Table 2 can be one of 'container', 'leaf-list', 'list', or 'leaf'. The 'container','leaf-list','list', or 'leaf' node not representing a snapshot of the current state for a set of data MUST not be tagged. The notification and action nodes MUST not be tagged.

All tag values described in Table 2 can be inherited down the containment hierarchy if the data nodes tagged with those tag values is one of 'container', 'leaf-list', or 'list'.

9. IANA Considerations

9.1. YANG Data Node Tag Prefixes Registry

This document requests IANA to create "YANG Node Tag Prefixes" subregistry in "YANG Node Tag" registry.

Prefix entries in this registry should be short strings consisting of lowercase ASCII alpha-numeric characters and a final ":" character.

The allocation policy for this registry is Specification Required [RFC8126].

The Reference and Assignee values should be sufficient to identify and contact the organization that has been allocated the prefix.

There is no specific guidance for the Designated Expert and there is a presumption that a code point should be granted unless there is a compelling reason to the contrary. The initial values for this registry are as follows:

+----------+----------------------------------+-----------+----------+
| Prefix   | Description                      | Reference | Assignee |
+----------+----------------------------------+-----------+----------+
| ietf:    | IETF Tags allocated in the IANA  | [This     | IETF     |
|          | IETF YANG Node Tags              | document] |          |
|          | registry                         |           |          |
|          |                                  |           |          |
| vendor:  | Non-registered tags allocated by | [This     | IETF     |
|          | the module's implementer.        | document] |          |
|          |                                  |           |          |
| user:    | Non-registered tags allocated by | [This     | IETF     |
|          | and for the user.                | document] |          |
+----------+----------------------------------+-----------+----------+
Figure 2: Table 1

Other standards organizations (SDOs) wishing to allocate their own set of tags should request the allocation of a prefix from this registry.

9.2. IETF YANG Data Node Tags Registry

This document requests IANA to create "IETF Node Tags" subregistry in "YANG Node Tag" registry. This subregistry appears below "YANG Node Tag Prefixes" registry.

This subregistry allocates tags that have the registered prefix "ietf:". New values should be well considered and not achievable through a combination of already existing IETF tags.

The allocation policy for this subregistry is IETF Review with Expert Review[RFC8126]. The Designated Expert is expected to verify that IANA assigned tags conform to Net-Unicode as defined in [RFC5198], and shall not need normalization.

The initial values for this subregistry are as follows:

   +----------------------------+--------------------------+-----------+
   | Node Tag                   | Description              | Reference |
   +----------------------------+--------------------------+-----------+
   |                            |                          |           |
   | ietf:metric                |Represent metric data     | [This     |
   |                            |(e.g., ifstatistics)      | document] |
   |                            |associated with specific  |[Open      |
   |                            |node (e.g.,interfaces)    |  Metrics] |
   |                            |                          |           |
   | ietf:info                  |Represent texture info    | [This     |
   |                            |(e.g., software revision) | document] |
   |                            |associated with specific  |[Open      |
   |                            |node (e.g.,component)    |  Metrics] |
   |                            |                          |           |
   | ietf:delay                 |Represent the delay metric|[This      |
   |                            |data associated with      | document  |
   |                            |specific node.            |[RFC2681]  |
   |                            |                          |[RFC7679]  |
   |                            |                          |           |
   | ietf:jitter                |Represent the jitter metric [This     |
   |                            |data asociated with       |document]  |
   |                            |specific node.            |[RFC3393]  |
   |                            |                          |           |
   |                            |                          |           |
   | ietf:loss                  |Represent the loss metric | [This     |
   |                            |data associated with      | document] |
   |                            |specific node.            | [RFC7680] |
   |                            |                          | [RFC6673] |
   |                            |                          |           |
   | ietf:counter               |Represent any metric value| [This     |
   |                            |associated with specific  | document] |
   |                            |node that monotonically   |[Open      |
   |                            |increases over time,      |  Metrics] |
   |                            |starting from zero.       |           |
   |                            |                          |           |
   | ietf:gauge                 |Represent current         | [This     |
   |                            |measurements associated   | document] |
   |                            |with specific node        |[Open      |
   |                            |that may increase,        |  Metrics] |
   |                            |decrease or stay constant.|           |
   |                            |                          |           |
   | ietf:summary               |Represent the metric value| [This     |
   |                            |associated with specific  | document] |
   |                            |node that measures        | [Open     |
   |                            |distributions of discrete |  Metrics] |
   |                            |events without knowing    |           |
   |                            |predefined range.         |           |
   |                            |                          |           |
   | ietf:unknown               |Represent the metric value| [This     |
   |                            |associated with specific  | document] |
   |                            |node that can not         |[Open      |
   |                            |determine the type of     |  Metrics] |
   |                            |metric.                   |           |
   +----------------------------+--------------------------+-----------+
Figure 3: Table 2

9.3. Updates to the IETF XML Registry

This document registers the following namespace URIs in the "ns" subregistry within the "IETF XML Registry" [RFC3688]:

   URI: urn:ietf:params:xml:ns:yang:ietf-node-tags
   Registrant Contact: The IESG.
   XML: N/A; the requested URI is an XML namespace.

   URI: urn:ietf:params:xml:ns:yang:ietf-node-tags-state
   Registrant Contact: The IESG.
   XML: N/A; the requested URI is an XML namespace.

9.4. Updates to the YANG Module Names Registry

This document registers the following two YANG modules in the YANG Module Names registry [RFC6020] within the "YANG Parameters" registry:

   name: ietf-node-tags
   namespace: urn:ietf:params:xml:ns:yang:ietf-node-tags
   prefix: ntags
   reference: RFC XXXX

   name: ietf-node-tags-state
   namespace: urn:ietf:params:xml:ns:yang:ietf-node-tags-state
   prefix: ntags-s
   reference: RFC XXXX

10. Security Considerations

The YANG module specified in this document defines schema for data that is designed to be accessed via network management protocols such as NETCONF [RFC6241] or RESTCONF [RFC8040]. The lowest NETCONF layer is the secure transport layer, and the mandatory-to-implement secure transport is Secure Shell (SSH) [RFC6242]. The lowest RESTCONF layer is HTTPS, and the mandatory-to-implement secure transport is TLS [RFC8446].

The Network Configuration Access Control Model (NACM) [RFC8341] provides the means to restrict access for particular NETCONF or RESTCONF users to a preconfigured subset of all available NETCONF or RESTCONF protocol operations and content, e.g., the presence of tags may reveal information about the way in which data nodes or node instances are used and therefore providing access to private information or revealing an attack vector should be restricted. Note that appropriate privilege and security levels need to be applied to the addition and removal of user tags to ensure that a user receives the correct data.

This document adds the ability to associate node tag with data nodes or instances of data nodes within the YANG modules. This document does not define any actions based on these associations, and none are yet defined, and therefore it does not by itself introduce any new security considerations.

Users of the node tag meta-data may define various actions to be taken based on the node tag meta-data. These actions and their definitions are outside the scope of this document. Users will need to consider the security implications of any actions they choose to define, including the potential for a tag to get 'masked' by another user.

11. Acknowledgements

The authors would like to thank Ran Tao for his major contributions to the initial modeling and use cases.

The authors would also like to acknowledge the comments and suggestions received from Juergen Schoenwaelder, Andy Bierman, Lou Berger, Jaehoon Paul Jeong, Wei Wang, Yuan Zhang, Ander Liu, YingZhen Qu, Boyuan Yan, Adrian Farrel, and Mahesh Jethanandani.

12. Contributors

      Liang Geng
      Individual
      32 Xuanwumen West St, Xicheng District
      Beijing  10053

13. References

13.1. Normative References

[RFC2119]
Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, , <https://www.rfc-editor.org/info/rfc2119>.
[RFC3688]
Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688, DOI 10.17487/RFC3688, , <https://www.rfc-editor.org/info/rfc3688>.
[RFC5198]
Klensin, J. and M. Padlipsky, "Unicode Format for Network Interchange", RFC 5198, DOI 10.17487/RFC5198, , <https://www.rfc-editor.org/info/rfc5198>.
[RFC6020]
Bjorklund, M., Ed., "YANG - A Data Modeling Language for the Network Configuration Protocol (NETCONF)", RFC 6020, DOI 10.17487/RFC6020, , <https://www.rfc-editor.org/info/rfc6020>.
[RFC7950]
Bjorklund, M., Ed., "The YANG 1.1 Data Modeling Language", RFC 7950, DOI 10.17487/RFC7950, , <https://www.rfc-editor.org/info/rfc7950>.
[RFC8040]
Bierman, A., Bjorklund, M., and K. Watsen, "RESTCONF Protocol", RFC 8040, DOI 10.17487/RFC8040, , <https://www.rfc-editor.org/info/rfc8040>.
[RFC8126]
Cotton, M., Leiba, B., and T. Narten, "Guidelines for Writing an IANA Considerations Section in RFCs", BCP 26, RFC 8126, DOI 10.17487/RFC8126, , <https://www.rfc-editor.org/info/rfc8126>.
[RFC8174]
Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, , <https://www.rfc-editor.org/info/rfc8174>.
[RFC8341]
Bierman, A. and M. Bjorklund, "Network Configuration Access Control Model", STD 91, RFC 8341, DOI 10.17487/RFC8341, , <https://www.rfc-editor.org/info/rfc8341>.
[RFC8407]
Bierman, A., "Guidelines for Authors and Reviewers of Documents Containing YANG Data Models", BCP 216, RFC 8407, DOI 10.17487/RFC8407, , <https://www.rfc-editor.org/info/rfc8407>.
[RFC8446]
Rescorla, E., "The Transport Layer Security (TLS) Protocol Version 1.3", RFC 8446, DOI 10.17487/RFC8446, , <https://www.rfc-editor.org/info/rfc8446>.
[RFC8819]
Hopps, C., Berger, L., and D. Bogdanovic, "YANG Module Tags", RFC 8819, DOI 10.17487/RFC8819, , <https://www.rfc-editor.org/info/rfc8819>.

13.2. Informative References

[FCAPS]
International Telecommunication Union, "X.700 : Management framework for Open Systems Interconnection (OSI) for CCITT applications", , , <http://www.itu.int/rec/T-REC-X.700-199209-I/en>.
[OpenMetrics]
OpenMetrics, "OpenMetrics, a cloud-native, highly scalable metrics protocol", , , <https://github.com/OpenObservability/OpenMetrics/blob/main/specification/OpenMetrics.md>.
[RFC6022]
Scott, M. and M. Bjorklund, "YANG Module for NETCONF Monitoring", RFC 6022, DOI 10.17487/RFC6022, , <https://www.rfc-editor.org/info/rfc6022>.
[RFC6241]
Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed., and A. Bierman, Ed., "Network Configuration Protocol (NETCONF)", RFC 6241, DOI 10.17487/RFC6241, , <https://www.rfc-editor.org/info/rfc6241>.
[RFC6242]
Wasserman, M., "Using the NETCONF Protocol over Secure Shell (SSH)", RFC 6242, DOI 10.17487/RFC6242, , <https://www.rfc-editor.org/info/rfc6242>.
[RFC7952]
Lhotka, L., "Defining and Using Metadata with YANG", RFC 7952, DOI 10.17487/RFC7952, , <https://www.rfc-editor.org/info/rfc7952>.
[RFC8340]
Bjorklund, M. and L. Berger, Ed., "YANG Tree Diagrams", BCP 215, RFC 8340, DOI 10.17487/RFC8340, , <https://www.rfc-editor.org/info/rfc8340>.
[RFC8342]
Bjorklund, M., Schoenwaelder, J., Shafer, P., Watsen, K., and R. Wilton, "Network Management Datastore Architecture (NMDA)", RFC 8342, DOI 10.17487/RFC8342, , <https://www.rfc-editor.org/info/rfc8342>.
[RFC8526]
Bjorklund, M., Schoenwaelder, J., Shafer, P., Watsen, K., and R. Wilton, "NETCONF Extensions to Support the Network Management Datastore Architecture", RFC 8526, DOI 10.17487/RFC8526, , <https://www.rfc-editor.org/info/rfc8526>.
[RFC8639]
Voit, E., Clemm, A., Gonzalez Prieto, A., Nilsen-Nygaard, E., and A. Tripathy, "Subscription to YANG Notifications", RFC 8639, DOI 10.17487/RFC8639, , <https://www.rfc-editor.org/info/rfc8639>.
[RFC8641]
Clemm, A. and E. Voit, "Subscription to YANG Notifications for Datastore Updates", RFC 8641, DOI 10.17487/RFC8641, , <https://www.rfc-editor.org/info/rfc8641>.
[RFC8792]
Watsen, K., Auerswald, E., Farrel, A., and Q. Wu, "Handling Long Lines in Content of Internet-Drafts and RFCs", RFC 8792, DOI 10.17487/RFC8792, , <https://www.rfc-editor.org/info/rfc8792>.
[RFC9195]
Lengyel, B. and B. Claise, "A File Format for YANG Instance Data", RFC 9195, DOI 10.17487/RFC9195, , <https://www.rfc-editor.org/info/rfc9195>.
[RFC9196]
Lengyel, B., Clemm, A., and B. Claise, "YANG Modules Describing Capabilities for Systems and Datastore Update Notifications", RFC 9196, DOI 10.17487/RFC9196, , <https://www.rfc-editor.org/info/rfc9196>.
[RFC9371]
Baber, A. and P. Hoffman, "Registration Procedures for Private Enterprise Numbers (PENs)", RFC 9371, DOI 10.17487/RFC9371, , <https://www.rfc-editor.org/info/rfc9371>.

Appendix A. Instance Level Tunnel Tagging Example

In the example shown in the following figure,the 'tunnel-svc' data node is a list node defined in a 'example-tunnel-pm' module and has 7 child nodes: 'name','create-time','modified-time','average-latency','packet-loss','min-latency','max-latency' leaf node. In these child nodes, the 'name' leaf node is the key leaf for the 'tunnel-svc' list. Following is the tree diagram [RFC8340] for the "example-tunnel-pm" module:

module: example-tunnel-pm
        +--rw tunnel-svc* [name]
        |   +--rw name                      string
        |   +--ro create-time               yang:date-and-time
        |   +--ro modified-time             yang:date-and-time
        |   +--ro average-latency           yang:gauge64
        |   +--ro packet-loss               yang:counter64
        |   +--ro min-latency               yang:gauge64
        |   +--ro max-latency               yang:gauge64

To help identify specific data for a customer, users tags on specific instances of the data nodes [RFC9195][RFC9196] are created as follows:

   <rpc message-id="103"
        xmlns="urn:ietf:params:xml:ns:netconf:base:1.0">
     <edit-data xmlns="urn:ietf:params:xml:ns:yang:ietf-netconf-nmda"
                xmlns:ds="urn:ietf:params:xml:ns:yang:ietf-datastores">
       <datastore>ds:running</datastore>
       <config>
       <module-tag>
        <module>
        <name>example-tunnel-pm</name>
         <node-tags
           xmlns="urn:ietf:params:xml:ns:yang:ietf-node-tags">
         <node>
           <id>1743</id>
           <node-selector>/tp:tunnel-svc[name='foo']/tp:packet-loss
            /</name>
           <tag>user:customer1_example_com</tag>
           <tag>user:critical</tag>
         </node>
         <node>
           <id>1744</id>
           <node-selector>/tp:tunnel-svc[name='bar']/tp:modified-time
           /</node-selctor>
           <tag>user:customer2_example_com</tag>
         </node>
       </node-tags>
      </module>
      </module-tag>
       </config>
     </edit-data>
   </rpc>

Note that the 'user:critical' tag is one addtional new tag value.

Appendix B. NETCONF Example

The following is a NETCONF example result from a query of node tags list. For the sake of brevity only a few module and associated data node results are provided. The example uses the folding defined in [RFC8792].

=============== NOTE: '\' line wrapping per RFC 8792 ================

<ns0:data xmlns:ns0="urn:ietf:params:xml:ns:netconf:base:1.0">
 <t:module-tags xmlns:t="urn:ietf:params:xml:ns:yang:ietf-module-tags">
    <t:module>
       <t:name>ietf-interfaces</t:name>
       <s:node-tags
         xmlns:s="urn:ietf:params:xml:ns:yang:ietf-node-tags">
        <s:node>
         <s:id>1723</s:id>
         <s:node-selector>
          /if:interfaces/if:interface/if:statistics/if:in-errors
         </s:node-selector>
         <s:tag>ietf:metric</s:tag>
         <s:tag>ietf:loss</s:tag>
         <s:tag>vendor:agg</s:tag>
        </s:node>
      </s:node-tags>
    </t:module>
    <t:module>
       <t:name>ietf-ip</t:name>
       <s:node-tags
         xmlns:s="urn:ietf:params:xml:ns:yang:ietf-node-tags">
        <s:node>
        <s:id>1733</s:id>
        <s:node-selector>/if:interfaces/if:interface/ip:ipv4/ip:mtu
        </s:node-selector>
        <s:tag>ietf:metric</s:tag>
       </s:node>
      </s:node-tags>
    </t:module>
  </t:module-tags>
</ns0:data>
Figure 4: Example NETCONF Query Output

Appendix C. Non-NMDA State Module

As per [RFC8407], the following is a non-NMDA module to support viewing the operational state for non-NMDA compliant servers.

<CODE BEGINS> file "[email protected]"

module ietf-node-tags-state {
  yang-version 1.1;
  namespace
        "urn:ietf:params:xml:ns:yang:ietf-node-tags-state";
  prefix ntags-s;

  import ietf-netconf-acm {
    prefix nacm;
    reference
    "RFC 8341: Network Configuration Access Control
               Model";
  }
  import ietf-module-tags {
    prefix tags;
  }
  import ietf-module-tags-state {
    prefix tags-s;
    reference
    "RFC 8819: YANG Module Tags ";
  }
  organization
    "IETF NetMod Working Group (NetMod)";

  contact
   "WG Web: <https://datatracker.ietf.org/wg/netmod/>
    WG List:<mailto:[email protected]>

    Editor: Qin Wu
            <mailto:[email protected]>

    Editor: Benoit Claise
            <mailto:[email protected]>

    Editor: Mohamed Boucadair
            <mailto:[email protected]>

    Editor: Peng Liu
            <mailto:[email protected]>

    Editor: Zongpeng Du
            <mailto:[email protected]>";
   // RFC Ed.: replace XXXX with actual RFC number and
   // remove this note.
  description
    "This module describes a mechanism associating data node
     tags with YANG data node within YANG modules. Tags may be
     IANA assigned or privately defined.

     Copyright (c) 2022 IETF Trust and the persons identified as
     authors of the code. All rights reserved.

     Redistribution and use in source and binary forms, with or
     without modification, is permitted pursuant to, and subject
     to the license terms contained in, the Simplified BSD License
     set forth in Section 4.c of the IETF Trust's Legal Provisions
     Relating to IETF Documents
     (https://trustee.ietf.org/license-info).

     This version of this YANG module is part of RFC XXXX
     (https://datatracker.ietf.org/html/rfcXXXX); see the RFC
     itself for full legal notices.";

   // RFC Ed.: update the date below with the date of RFC publication
   // and RFC number and remove this note.
  revision 2022-02-04 {
    description
      "Initial revision.";
    reference
      "RFC XXXX: Node Tags in YANG Data
                 Modules";
  }
  augment "/tags-s:module-tags-state/tags-s:module" {
    description
      "Augments the Module Tags module with node tag
       attributes.";
    container node-tags {
      config false;
      status deprecated;
      description
        "Contains the list of data nodes and their
         associated self describing tags.";
      list node {
        key "id";
        status deprecated;
        description
          "Lists the data nodes and their associated self
           describing tags.";
        leaf id {
          type uint64;
          description
          "Identification of each data node within YANG module. It is
           unique 64-bit unsigned integers.";
        }
        leaf node-selctor {
          type nacm:node-instance-identifier;
          mandatory true;
          status deprecated;
          description
            "Selects the data nodes for which tags are
             specified.";
        }
       leaf-list tags {
          type tags:tag;
          status deprecated;
          description
            "Lists the tags associated with the data node within
             the YANG  module.

             See the IANA 'YANG Node Tag Prefixes' registry
             for reserved prefixes and the IANA 'IETF YANG Data
             Node Tags' registry for IETF tags.

             The 'operational' state view of this list is
             constructed using the following steps:

             1) System tags (i.e., tags of 'system' origin) are
                added.
             2) User configured tags (i.e., tags of 'intended'
                origin) are added.
             3) Any tag that is equal to a masked-tag is removed.";
          reference
            "RFC XXXX: Node Tags in YANG Data
                       Modules, Section 9";
     }
        leaf-list masked-tag {
          type tags:tag;
          status deprecated;
          description
            "The list of tags that should not be associated with the
             data node within the YANG module. The user can remove
             (mask) tags from the operational state datastore by
             adding them to this list. It is not an error to add
             tags to this list that are not associated with the
             data node within YANG module, but they have no
             operational effect.";
        }
      }
    }
  }
}

<CODE ENDS>

Appendix D. Targeted Data Fetching Example

The following provides tagged data node Fetching example. The subscription "id" values of 22 used below is just an example. In production, the actual values of "id" might not be small integers.

+-----------+                        +-----------+
| Subscriber|                        | Publisher |
+-----+-----+                        +-----+-----+
      |                                    |
      |      Node Tagging Fetching         |
      |    (id, node-tag = metric)         |
      |<-----------------------------------+
      |                                    |
      |     establish-subscription         |
      +----------------------------------->|
      |                                    |
      |       RPC Reply: OK, id = 22       |
      |<-----------------------------------+
      |                                    |
      |    Notification Message (for 22)   |
      |<-----------------------------------+
      |                                    |

The subscriber can query node tag list from operational datastore in the network device using "ietf-node-tags" module defined in this document and fetch tagged data node instances and associated data path to the datastore node. The node tag information instruct the receiver to subscribe tagged data node (e.g., performance metric data nodes) using standard subscribed notification mechanism [RFC8639] [RFC8641].

=============== NOTE: '\' line wrapping per RFC 8792 ================

<?xml version="1.0" encoding="UTF-8"?>
    <t:module-tags
      xmlns:t="urn:ietf:params:xml:ns:yang:ietf-module-tags">
       <t:module>
          <t:name>ietf-interfaces</t:name>
          <s:node-tags
            xmlns:s="urn:ietf:params:xml:ns:yang:ietf-node-tags">
           <s:node>
            <s:id>1723</s:id>
            <s:node-selector>/if:interfaces/if:interface/if:in-errors
            /</s:node-selector>
            <s:tag>ietf:metric</s:tag>
            <s:tag>ietf:loss</s:tag>
           </s:node>
           </s:node-tags>
      </t:module>
    </module-tags>
Figure 5: List of Available Target Objects

With node tag information returned,e.g., in the 'get-data' operation, the subscriber identifies tagged data node and associated data path to the datastore node and sends a standard establish-subscription RPC [RFC8639]and [RFC8641] to subscribe tagged data nodes that are interests to the client application from the publisher. The publisher returns specific data node types of operational state (e.g., in-errors statistics data) subscribed by the client as follows:

=============== NOTE: '\' line wrapping per RFC 8792 ================

 <netconf:rpc message-id="101"
     xmlns:netconf="urn:ietf:params:xml:ns:netconf:base:1.0">
   <establish-subscription
       xmlns="urn:ietf:params:xml:ns:yang:ietf-subscribed-notifica\
       tions"
       xmlns:yp="urn:ietf:params:xml:ns:yang:ietf-yang-push">
     <yp:datastore
          xmlns:ds="urn:ietf:params:xml:ns:yang:ietf-datastores">
       ds:operational
     </yp:datastore>
     <yp:datastore-xpath-filter
         xmlns:ex="https://example.com/sample-data/1.0">
       /if:interfaces/if:interface/if:statistics/if:in-errors
     </yp:datastore-xpath-filter>
     <yp:periodic>
       <yp:period>500</yp:period>
     </yp:periodic>
   </establish-subscription>
 </netconf:rpc>

Appendix E. Changes between Revisions

Editorial Note (To be removed by RFC Editor)

v09 - v10

v08 - v09

v07 - v08

v06 - v07

v05 - v06

v04 - v05

v03 - v04

v02 - v03

v01 - v02

v00 - v01

Authors' Addresses

Qin Wu
Huawei
101 Software Avenue, Yuhua District
Nanjing
Jiangsu, 210012
China
Benoit Claise
Huawei
De Kleetlaan 6a b1
1831 Diegem
Belgium
Mohamed Boucadair
Orange
35000 Rennes
France
Peng Liu
China Mobile
32 Xuanwumen West St, Xicheng District
Beijing
Zongpeng Du
China Mobile
32 Xuanwumen West St, Xicheng District
Beijing