Internet-Draft MPLS TE Tunnels YANG Data Model May 2023
Saad, et al. Expires 27 November 2023 [Page]
Workgroup:
TEAS Working Group
Internet-Draft:
draft-ietf-teas-yang-te-mpls-04
Published:
Intended Status:
Standards Track
Expires:
Authors:
T. Saad
Cisco Systems Inc
R. Gandhi
Cisco Systems Inc
X. Liu
IBM Corporation
V. P. Beeram
Juniper Networks
I. Bryskin
Individual

A YANG Data Model for MPLS Traffic Engineering Tunnels

Abstract

This document defines a YANG data model for the configuration and management of Multiprotocol Label Switching (MPLS) Traffic Engineering (TE) tunnels, Label Switched Paths (LSPs) and interfaces. The model augments the TE generic YANG model for MPLS packet dataplane technology.

This model covers data for configuration, operational state, remote procedural calls, and event notifications.

Status of This Memo

This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.

Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.

Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."

This Internet-Draft will expire on 27 November 2023.

Table of Contents

1. Introduction

YANG [RFC6020] and [RFC7950] is a data modeling language used to define the contents of a conceptual data store that allows networked devices to be managed using NETCONF [RFC6241]. YANG has proved relevant beyond its initial confines, as bindings to other interfaces (e.g. RESTCONF [RFC8040]) and encoding other than XML (e.g. JSON) are being defined. Furthermore, YANG data models can be used as the basis of implementation for other interfaces, such as CLI and programmatic APIs.

This document describes the YANG data model for configuration and management of MPLS TE tunnels, LSPs, and interfaces. Other YANG module(s) that model the establishment of MPLS LSP(s) via signaling protocols such as RSVP-TE ([RFC3209], [RFC3473]) are described in separate document(s).

1.1. Terminology

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here.

The terminology for describing YANG data models is found in [RFC7950].

1.2. Prefixes in Data Node Names

In this document, names of data nodes and other data model objects are prefixed using the standard prefix associated with the corresponding YANG imported modules, as shown in Table 1.

Table 1: Prefixes and corresponding YANG modules
Prefix YANG module Reference
yang ietf-yang-types [RFC6991]
inet ietf-inet-types [RFC6991]
rt-types ietf-routing-types [RFC8294]
te ietf-te [I-D.ietf-teas-yang-te]
te-mpls ietf-te-mpls This document
te-types ietf-te-types [RFC8776]

1.3. Acronyms and Abbreviations

  • MPLS: Multiprotocol Label Switching LSP: Label Switched Path LSR: Label Switching Router LER: Label Edge Router TE: Traffic Engineering

2. MPLS TE YANG Model

The MPLS TE YANG model covers the configuration, state, RPC and notifications data pertaining to MPLS TE interfaces, tunnels and LSPs parameters. The data specific to the signaling protocol used to establish MPLS LSP(s) is outside the scope of this document and is covered in other documents.

2.1. Module(s) Relationship

The MPLS TE YANG module "ietf-te-mpls" imports the following modules:

This module references the following documents: [RFC8233], [RFC4710], [RFC8570], and [RFC4124].

                   +---------+         o: augment
                   | ietf-te |
                   +---------+
                      o  o
                      |  |
                +-----+  +-----+
                |              |
          +---------------+   +--------------+
          | ietf-rsvp-te^ |--o| ietf-te-mpls |
          +---------------+   +--------------+

                X---oY indicates that module X augments module Y
                ^ indicates a module defined in other documents
Figure 1: Relationship of MPLS TE module with TE generic and RSVP-TE YANG modules

The MPLS TE YANG module "ietf-te-mpls" augments the "ietf-te" TE generic YANG module as shown in Figure 1.

2.2. Model Tree Diagram

Figure 2 shows the tree diagram of the MPLS TE YANG model that is defined in ietf-te-mpls.yang.

module: ietf-te-mpls
  augment /te:te/te-dev:performance-thresholds:
    +--rw throttle
       +--rw one-way-delay-offset?                  uint32
       +--rw measure-interval?                      uint32
       +--rw advertisement-interval?                uint32
       +--rw suppression-interval?                  uint32
       +--rw threshold-out
       |  +--rw one-way-delay?                 uint32
       |  +--rw one-way-residual-bandwidth?
       |  |       rt-types:bandwidth-ieee-float32
       |  +--rw one-way-available-bandwidth?
       |  |       rt-types:bandwidth-ieee-float32
       |  +--rw one-way-utilized-bandwidth?
       |  |       rt-types:bandwidth-ieee-float32
       |  +--rw two-way-delay?                 uint32
       |  +--rw one-way-min-delay?             uint32
       |  +--rw one-way-max-delay?             uint32
       |  +--rw one-way-delay-variation?       uint32
       |  +--rw one-way-packet-loss?           decimal64
       |  +--rw two-way-min-delay?             uint32
       |  +--rw two-way-max-delay?             uint32
       |  +--rw two-way-delay-variation?       uint32
       |  +--rw two-way-packet-loss?           decimal64
       +--rw threshold-in
       |  +--rw one-way-delay?                 uint32
       |  +--rw one-way-residual-bandwidth?
       |  |       rt-types:bandwidth-ieee-float32
       |  +--rw one-way-available-bandwidth?
       |  |       rt-types:bandwidth-ieee-float32
       |  +--rw one-way-utilized-bandwidth?
       |  |       rt-types:bandwidth-ieee-float32
       |  +--rw two-way-delay?                 uint32
       |  +--rw one-way-min-delay?             uint32
       |  +--rw one-way-max-delay?             uint32
       |  +--rw one-way-delay-variation?       uint32
       |  +--rw one-way-packet-loss?           decimal64
       |  +--rw two-way-min-delay?             uint32
       |  +--rw two-way-max-delay?             uint32
       |  +--rw two-way-delay-variation?       uint32
       |  +--rw two-way-packet-loss?           decimal64
       +--rw threshold-accelerated-advertisement
          +--rw one-way-delay?                 uint32
          +--rw one-way-residual-bandwidth?
          |       rt-types:bandwidth-ieee-float32
          +--rw one-way-available-bandwidth?
          |       rt-types:bandwidth-ieee-float32
          +--rw one-way-utilized-bandwidth?
          |       rt-types:bandwidth-ieee-float32
          +--rw two-way-delay?                 uint32
          +--rw one-way-min-delay?             uint32
          +--rw one-way-max-delay?             uint32
          +--rw one-way-delay-variation?       uint32
          +--rw one-way-packet-loss?           decimal64
          +--rw two-way-min-delay?             uint32
          +--rw two-way-max-delay?             uint32
          +--rw two-way-delay-variation?       uint32
          +--rw two-way-packet-loss?           decimal64
  augment /te:te/te:tunnels/te:tunnel:
    +--rw tunnel-igp-shortcut
    |  +--rw shortcut-eligible?   boolean
    |  +--rw metric-type?         identityref
    |  +--rw metric?              int32
    |  +--rw routing-afs*         inet:ip-version
    +--rw forwarding
    |  +--rw binding-label?   rt-types:mpls-label
    |  +--rw load-share?      uint32
    |  +--rw policy-class?    uint8
    +--rw bandwidth-mpls
       +--rw specification-type?
       |       te-packet-types:te-bandwidth-requested-type
       +--rw set-bandwidth?        te-packet-types:bandwidth-kbps
       +--rw class-type?           te-types:te-ds-class
       +--ro state
       |  +--ro signaled-bandwidth?   te-packet-types:bandwidth-kbps
       +--rw auto-bandwidth
          +--rw enabled?            boolean
          +--rw min-bw?             te-packet-types:bandwidth-kbps
          +--rw max-bw?             te-packet-types:bandwidth-kbps
          +--rw adjust-interval?    uint32
          +--rw adjust-threshold?   rt-types:percentage
          +--rw overflow
          |  +--rw enabled?               boolean
          |  +--rw overflow-threshold?    rt-types:percentage
          |  +--rw trigger-event-count?   uint16
          +--rw underflow
             +--rw enabled?               boolean
             +--rw underflow-threshold?   rt-types:percentage
             +--rw trigger-event-count?   uint16
  augment /te:te/te:tunnels/te:tunnel/te:primary-paths/te:primary-path:
    +--rw static-lsp-name?   mpls-static:static-lsp-ref
  augment /te:te/te:tunnels/te:tunnel/te:secondary-paths
            /te:secondary-path:
    +--rw static-lsp-name?   mpls-static:static-lsp-ref
  augment /te:te/te:globals/te:named-path-constraints
            /te:named-path-constraint:
    +--rw bandwidth
       +--rw specification-type?
       |       te-packet-types:te-bandwidth-requested-type
       +--rw set-bandwidth?        te-packet-types:bandwidth-kbps
       +--rw class-type?           te-types:te-ds-class
       +--ro state
          +--ro signaled-bandwidth?   te-packet-types:bandwidth-kbps
  augment /te:te/te:tunnels/te:tunnel/te:primary-paths/te:primary-path
            /te:lsps/te:lsp:
    +--ro performance-metrics-one-way
    |  +--ro one-way-delay?                           uint32
    |  +--ro one-way-delay-normality?
    |  |       te-types:performance-metrics-normality
    |  +--ro one-way-residual-bandwidth?
    |  |       rt-types:bandwidth-ieee-float32
    |  +--ro one-way-residual-bandwidth-normality?
    |  |       te-types:performance-metrics-normality
    |  +--ro one-way-available-bandwidth?
    |  |       rt-types:bandwidth-ieee-float32
    |  +--ro one-way-available-bandwidth-normality?
    |  |       te-types:performance-metrics-normality
    |  +--ro one-way-utilized-bandwidth?
    |  |       rt-types:bandwidth-ieee-float32
    |  +--ro one-way-utilized-bandwidth-normality?
    |  |       te-types:performance-metrics-normality
    |  +--ro one-way-min-delay?                       uint32
    |  +--ro one-way-min-delay-normality?
    |  |       te-types:performance-metrics-normality
    |  +--ro one-way-max-delay?                       uint32
    |  +--ro one-way-max-delay-normality?
    |  |       te-types:performance-metrics-normality
    |  +--ro one-way-delay-variation?                 uint32
    |  +--ro one-way-delay-variation-normality?
    |  |       te-types:performance-metrics-normality
    |  +--ro one-way-packet-loss?                     decimal64
    |  +--ro one-way-packet-loss-normality?
    |          te-types:performance-metrics-normality
    +--ro performance-metrics-two-way
       +--ro two-way-delay?                       uint32
       +--ro two-way-delay-normality?
       |       te-types:performance-metrics-normality
       +--ro two-way-min-delay?                   uint32
       +--ro two-way-min-delay-normality?
       |       te-types:performance-metrics-normality
       +--ro two-way-max-delay?                   uint32
       +--ro two-way-max-delay-normality?
       |       te-types:performance-metrics-normality
       +--ro two-way-delay-variation?             uint32
       +--ro two-way-delay-variation-normality?
       |       te-types:performance-metrics-normality
       +--ro two-way-packet-loss?                 decimal64
       +--ro two-way-packet-loss-normality?
               te-types:performance-metrics-normality
Figure 2: MPLS TE model configuration and state tree

2.3. MPLS TE YANG Module

<CODE BEGINS> file "[email protected]"

module ietf-te-mpls {
  yang-version 1.1;
  namespace "urn:ietf:params:xml:ns:yang:ietf-te-mpls";

  /* Replace with IANA when assigned */
  prefix "te-mpls";

  /* Import TE base model */
  import ietf-te {
    prefix te;
    reference "draft-ietf-teas-yang-te: A YANG Data Model for Traffic
               Engineering Tunnels and Interfaces";
  }

  /* Import TE MPLS types */
  import ietf-te-packet-types {
    prefix "te-packet-types";
    reference "RFC8776: A YANG Data Model for
               Common Traffic Engineering Types";
  }

  /* Import TE generic types */
  import ietf-te-types {
    prefix te-types;
    reference "RFC8776: A YANG Data Model for
               Common Traffic Engineering Types";
  }

  /* Import routing types */
  import ietf-routing-types {
    prefix rt-types;
    reference "RFC8294: Common YANG Data Types for the Routing Area";
  }

  import ietf-mpls-static {
    prefix mpls-static;
    reference "draft-ietf-mpls-static-yang: A YANG Data Model
               for MPLS Static LSPs";
  }

  import ietf-inet-types {
    prefix inet;
    reference "RFC6991: Common YANG Data Types";
  }

  organization
    "IETF Traffic Engineering Architecture and Signaling (TEAS)
     Working Group";

  contact
    "WG Web:   <http://tools.ietf.org/wg/teas/>
     WG List:  <mailto:[email protected]>

     Editor:   Tarek Saad
               <mailto:[email protected]>

     Editor:   Rakesh Gandhi
               <mailto:[email protected]>

     Editor:   Vishnu Pavan Beeram
               <mailto:[email protected]>

     Editor:   Xufeng Liu
               <mailto: [email protected]>

     Editor:   Igor Bryskin
               <mailto:[email protected]>";

  description
    "YANG data module for MPLS TE configurations,
     state, RPC and notifications. The model fully conforms to
     the Network Management Datastore Architecture (NMDA).

     Copyright (c) 2018 IETF Trust and the persons
     identified as authors of the code.  All rights reserved.

     Redistribution and use in source and binary forms, with or
     without modification, is permitted pursuant to, and subject
     to the license terms contained in, the Simplified BSD License
     set forth in Section 4.c of the IETF Trust's Legal Provisions
     Relating to IETF Documents
     (https://trustee.ietf.org/license-info).
     This version of this YANG module is part of RFC XXXX; see
     the RFC itself for full legal notices.";

  // RFC Ed.: replace XXXX with actual RFC number and remove this
  // note.

  // RFC Ed.: update the date below with the date of RFC publication
  // and remove this note.

  revision "2023-05-25" {
    description "Latest update to MPLS TE YANG module.";
    reference
      "RFCXXXX: A YANG Data Model for MPLS-TE Tunnels and LSP(s)";
  }

  /* MPLS TE Identities */
  identity tunnel-action-resetup {
    base te-types:tunnel-action-type;
    description "Resetup tunnel action type";
  }

  identity path-metric-loss {
    base te-types:path-metric-type;
    description
      "The path loss metric type (as a packet percentage) that
       encodes a function of the unidirectional loss metrics of all
       links traversed by a P2P path. The basic unit is 0.000003%,
       where (2^24 - 2) or 50.331642% is the highest packet-loss
       percentage that can be expressed.";
    reference "RFC8233, RFC4710, and RFC8570";
  }

  /* MPLS TE tunnel properties*/
  grouping tunnel-igp-shortcut-config {
    description "TE tunnel IGP shortcut configs";
    leaf shortcut-eligible {
      type boolean;
      default "true";
      description
        "Whether this LSP is considered to be eligible for us as a
        shortcut in the IGP. In the case that this leaf is set to
        true, the IGP SPF calculation uses the metric specified to
        determine whether traffic should be carried over this LSP";
    }
    leaf metric-type {
      type identityref {
        base te-types:lsp-metric-type;
      }
      default te-types:lsp-metric-inherited;
      description
        "The type of metric specification that should be used to set
        the LSP(s) metric";
    }
    leaf metric {
      type int32;
      description
        "The value of the metric that should be specified. The value
        supplied in this leaf is used in conjunction with the metric
        type to determine the value of the metric used by the system.
        Where the metric-type is set to lsp-metric-absolute - the
        value of this leaf is used directly; where it is set to
        lsp-metric-relative, the relevant (positive or negative)
        offset is used to formulate the metric; where metric-type
        is lsp-metric-inherited, the value of this leaf is not
        utilized";
    }
    leaf-list routing-afs {
      type inet:ip-version;
      description
        "Address families";
    }
  }

  grouping tunnel-igp-shortcuts {
    description
      "TE tunnel IGP shortcut grouping";
    container tunnel-igp-shortcut {
      description
        "Tunnel IGP shortcut properties";
      uses tunnel-igp-shortcut-config;
    }
  }

  grouping tunnel-forwarding-adjacency-configs {
    description "Tunnel forwarding adjacency grouping";
    leaf binding-label {
      type rt-types:mpls-label;
      description "MPLS tunnel binding label";
    }
    leaf load-share {
      type uint32 {
        range "1..4294967295";
      }
      description "ECMP tunnel forwarding
        load-share factor.";
    }
    leaf policy-class {
      type uint8 {
        range "1..7";
      }
      description
        "The class associated with this tunnel";
    }
  }

  grouping tunnel-forwarding-adjacency {
    description "Properties for using tunnel in forwarding.";
    container forwarding {
      description
        "Tunnel forwarding properties container";
      uses tunnel-forwarding-adjacency-configs;
    }
  }

  /*** End of MPLS TE tunnel configuration/state */
  grouping te-lsp-auto-bandwidth-config {
    description
      "Configuration parameters related to autobandwidth";

    leaf enabled {
      type boolean;
      default false;
      description
        "Enables MPLS auto-bandwidth on the
         LSP";
    }

    leaf min-bw {
      type te-packet-types:bandwidth-kbps;
      description
        "set the minimum bandwidth in Kbps for an
         auto-bandwidth LSP";
    }

    leaf max-bw {
      type te-packet-types:bandwidth-kbps;
      description
        "set the maximum bandwidth in Kbps for an
         auto-bandwidth LSP";
    }

    leaf adjust-interval {
      type uint32;
      description
        "time in seconds between adjustments to
         LSP bandwidth";
    }

    leaf adjust-threshold {
      type rt-types:percentage;
      description
        "percentage difference between the LSP's
         specified bandwidth and its current bandwidth
         allocation -- if the difference is greater than the
         specified percentage, auto-bandwidth adjustment is
         triggered";
    }
  }

  grouping te-lsp-overflow-config {
    description
     "configuration for MPLS LSP bandwidth
      overflow adjustment";

    leaf enabled {
      type boolean;
      default false;
      description
       "Enables MPLS LSP bandwidth overflow
        adjustment on the LSP";
    }

    leaf overflow-threshold {
      type rt-types:percentage;
      description
       "bandwidth percentage change to trigger
        an overflow event";

    }

    leaf trigger-event-count {
      type uint16;
      description
       "number of consecutive overflow sample
        events needed to trigger an overflow adjustment";
    }
  }

  grouping te-lsp-underflow-config {
    description
      "configuration for MPLS LSP bandwidth
      underflow adjustment";

    leaf enabled {
      type boolean;
      default false;
      description
       "enables bandwidth underflow
        adjustment on the LSP";
    }

    leaf underflow-threshold {
      type rt-types:percentage;
      description
       "bandwidth percentage change to trigger
        and underflow event";
    }

    leaf trigger-event-count {
      type uint16;
      description
       "number of consecutive underflow sample
        events needed to trigger an underflow adjustment";
    }
  }
  grouping te-tunnel-bandwidth-config {
    description
      "Configuration parameters related to bandwidth for a tunnel";

    leaf specification-type {
      type te-packet-types:te-bandwidth-requested-type;
      default specified;
      description
        "The method used for setting the bandwidth, either explicitly
         specified or configured";
    }

    leaf set-bandwidth {
      when "../specification-type = 'specified'" {
       description
         "The bandwidth value when bandwidth is explicitly
          specified";
      }
      type te-packet-types:bandwidth-kbps;
      description
       "set bandwidth explicitly, e.g., using
        offline calculation";
    }
    leaf class-type {
      type te-types:te-ds-class;
      description
        "The Class-Type of traffic transported by the LSP.";
      reference "RFC4124: section-4.3.1";
    }
  }

  grouping te-tunnel-bandwidth-state {
    description
      "Operational state parameters relating to bandwidth for
       a tunnel";

    leaf signaled-bandwidth {
      type te-packet-types:bandwidth-kbps;
      description
        "The currently signaled bandwidth of the LSP. In the case
         where the bandwidth is specified explicitly, then this will
         match the value of the set-bandwidth leaf; in cases where
         the bandwidth is dynamically computed by the system, the
         current value of the bandwidth should be reflected.";
    }
  }

  grouping tunnel-bandwidth_top {
    description
      "Top level grouping for specifying bandwidth for a tunnel";

    container bandwidth-mpls {
      description
        "Bandwidth configuration for TE LSPs";

      uses te-tunnel-bandwidth-config;

      container state {
        config false;
        description
          "State parameters related to bandwidth
          configuration of TE tunnels";
        uses te-tunnel-bandwidth-state;
      }

      container auto-bandwidth {
        when "../specification-type = 'auto'" {
          description
            "Include this container for auto bandwidth
            specific configuration";
        }
        description
          "Parameters related to auto-bandwidth";

        uses te-lsp-auto-bandwidth-config;

        container overflow {
          description
            "configuration of MPLS overflow bandwidth
            adjustment for the LSP";

          uses te-lsp-overflow-config;
        }

        container underflow {
          description
            "configuration of MPLS underflow bandwidth
            adjustment for the LSP";

          uses te-lsp-underflow-config;
        }
      }
    }
  }

  grouping te-path-bandwidth_top {
    description
      "Top level grouping for specifying bandwidth for a TE path";

    container bandwidth {
      description
        "Bandwidth configuration for TE LSPs";

      uses te-tunnel-bandwidth-config;
      container state {
        config false;
        description
          "State parameters related to bandwidth
          configuration of TE tunnels";
        uses te-tunnel-bandwidth-state;
      }
    }
  }



  /**
   * MPLS TE augmentations
   */
  augment "/te:te" {
    container performance-thresholds {
      uses "te-packet-types:" +
        "performance-metrics-throttle-container-packet";
        description
          "Performance parameters configurable thresholds";
    }
    description
      "Performance parameters configurable thresholds";
  }

  /* MPLS TE interface augmentations */


  /* MPLS TE tunnel augmentations */
  augment "/te:te/te:tunnels/te:tunnel" {
    description "MPLS TE tunnel config augmentations";
    uses tunnel-igp-shortcuts;
    uses tunnel-forwarding-adjacency;
    uses tunnel-bandwidth_top;
  }

  /* MPLS TE LSPs augmentations */
  augment "/te:te/te:tunnels/te:tunnel/" +
          "te:primary-paths/te:primary-path" {
    when "/te:te/te:tunnels/te:tunnel" +
      "/te:primary-paths/te:primary-path" +
      "/te:signaling-type = 'te-types:path-setup-static'" {
      description
      "When the path is statically provisioned";
    }
    description "MPLS TE LSP augmentation";
    leaf static-lsp-name {
      type mpls-static:static-lsp-ref;
      description "Static LSP name";
    }
  }

  augment "/te:te/te:tunnels/te:tunnel/" +
          "te:secondary-paths/te:secondary-path" {
    when "/te:te/te:tunnels/te:tunnel" +
      "/te:secondary-paths/te:secondary-path/" +
      "te:signaling-type = 'te-types:path-setup-static'" {
      description
      "When the path is statically provisioned";
    }
    description "MPLS TE LSP augmentation";
    leaf static-lsp-name {
      type mpls-static:static-lsp-ref;
      description "Static LSP name";
    }
  }

  augment "/te:te/te:globals/te:named-path-constraints/" +
          "te:named-path-constraint" {
    description "foo";
    uses te-path-bandwidth_top;
  }

  augment "/te:te/te:tunnels/te:tunnel/te:primary-paths" +
          "/te:primary-path/te:lsps/te:lsp" {
    description
      "MPLS TE generic data augmentation pertaining to specific TE
       LSP";
    uses te-packet-types:performance-metrics-attributes-packet;
  }
}

<CODE ENDS>
Figure 3: TE generic YANG module

3. IANA Considerations

This document registers the following URIs in the IETF XML registry [RFC3688]. Following the format in [RFC3688], the following registration is requested to be made.

   URI: urn:ietf:params:xml:ns:yang:ietf-te-mpls
   XML: N/A, the requested URI is an XML namespace.

This document registers a YANG module in the YANG Module Names registry [RFC6020].

   name:       ietf-te-mpls
   namespace:  urn:ietf:params:xml:ns:yang:ietf-te-mpls
   prefix:     ietf-te-mpls
   reference:  RFC3209

4. Security Considerations

The YANG module defined in this memo is designed to be accessed via the NETCONF protocol [RFC6241]. The lowest NETCONF layer is the secure transport layer and the mandatory-to-implement secure transport is SSH [RFC6242]. The NETCONF access control model [RFC8341] provides means to restrict access for particular NETCONF users to a pre-configured subset of all available NETCONF protocol operations and content.

A number of data nodes defined in this YANG module are writable/creatable/deletable (i.e., config true, which is the default). These data nodes may be considered sensitive or vulnerable in some network environments. Write operations (e.g., <edit-config>) to these data nodes without proper protection can have a negative effect on MPLS network operations. Following are the subtrees and data nodes and their sensitivity/vulnerability:

"/te/tunnels": The augmentation to this list specifies configuration to TE tunnels on a device. Unauthorized access to this list could cause the device to ignore packets it should receive and process.

"/te/globals": The augmentation to this target specifies configuration applicable to the to all or one TE device. Unauthorized access to this list could cause the device to ignore packets it should receive and process.

5. Contributors

   Himanshu Shah
   Ciena
   Email: [email protected]

6. Normative References

[I-D.ietf-mpls-static-yang]
Saad, T., Gandhi, R., Liu, X., Beeram, V. P., and I. Bryskin, "A YANG Data Model for MPLS Static LSPs", Work in Progress, Internet-Draft, draft-ietf-mpls-static-yang-13, , <https://datatracker.ietf.org/doc/html/draft-ietf-mpls-static-yang-13>.
[I-D.ietf-teas-yang-te]
Saad, T., Gandhi, R., Liu, X., Beeram, V. P., Bryskin, I., and O. G. de Dios, "A YANG Data Model for Traffic Engineering Tunnels, Label Switched Paths and Interfaces", Work in Progress, Internet-Draft, draft-ietf-teas-yang-te-32, , <https://datatracker.ietf.org/doc/html/draft-ietf-teas-yang-te-32>.
[RFC2119]
Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, DOI 10.17487/RFC2119, , <https://www.rfc-editor.org/info/rfc2119>.
[RFC3209]
Awduche, D., Berger, L., Gan, D., Li, T., Srinivasan, V., and G. Swallow, "RSVP-TE: Extensions to RSVP for LSP Tunnels", RFC 3209, DOI 10.17487/RFC3209, , <https://www.rfc-editor.org/info/rfc3209>.
[RFC3473]
Berger, L., Ed., "Generalized Multi-Protocol Label Switching (GMPLS) Signaling Resource ReserVation Protocol-Traffic Engineering (RSVP-TE) Extensions", RFC 3473, DOI 10.17487/RFC3473, , <https://www.rfc-editor.org/info/rfc3473>.
[RFC3688]
Mealling, M., "The IETF XML Registry", BCP 81, RFC 3688, DOI 10.17487/RFC3688, , <https://www.rfc-editor.org/info/rfc3688>.
[RFC4124]
Le Faucheur, F., Ed., "Protocol Extensions for Support of Diffserv-aware MPLS Traffic Engineering", RFC 4124, DOI 10.17487/RFC4124, , <https://www.rfc-editor.org/info/rfc4124>.
[RFC4710]
Siddiqui, A., Romascanu, D., and E. Golovinsky, "Real-time Application Quality-of-Service Monitoring (RAQMON) Framework", RFC 4710, DOI 10.17487/RFC4710, , <https://www.rfc-editor.org/info/rfc4710>.
[RFC6020]
Bjorklund, M., Ed., "YANG - A Data Modeling Language for the Network Configuration Protocol (NETCONF)", RFC 6020, DOI 10.17487/RFC6020, , <https://www.rfc-editor.org/info/rfc6020>.
[RFC6241]
Enns, R., Ed., Bjorklund, M., Ed., Schoenwaelder, J., Ed., and A. Bierman, Ed., "Network Configuration Protocol (NETCONF)", RFC 6241, DOI 10.17487/RFC6241, , <https://www.rfc-editor.org/info/rfc6241>.
[RFC6242]
Wasserman, M., "Using the NETCONF Protocol over Secure Shell (SSH)", RFC 6242, DOI 10.17487/RFC6242, , <https://www.rfc-editor.org/info/rfc6242>.
[RFC6991]
Schoenwaelder, J., Ed., "Common YANG Data Types", RFC 6991, DOI 10.17487/RFC6991, , <https://www.rfc-editor.org/info/rfc6991>.
[RFC7950]
Bjorklund, M., Ed., "The YANG 1.1 Data Modeling Language", RFC 7950, DOI 10.17487/RFC7950, , <https://www.rfc-editor.org/info/rfc7950>.
[RFC8040]
Bierman, A., Bjorklund, M., and K. Watsen, "RESTCONF Protocol", RFC 8040, DOI 10.17487/RFC8040, , <https://www.rfc-editor.org/info/rfc8040>.
[RFC8174]
Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, , <https://www.rfc-editor.org/info/rfc8174>.
[RFC8233]
Dhody, D., Wu, Q., Manral, V., Ali, Z., and K. Kumaki, "Extensions to the Path Computation Element Communication Protocol (PCEP) to Compute Service-Aware Label Switched Paths (LSPs)", RFC 8233, DOI 10.17487/RFC8233, , <https://www.rfc-editor.org/info/rfc8233>.
[RFC8294]
Liu, X., Qu, Y., Lindem, A., Hopps, C., and L. Berger, "Common YANG Data Types for the Routing Area", RFC 8294, DOI 10.17487/RFC8294, , <https://www.rfc-editor.org/info/rfc8294>.
[RFC8341]
Bierman, A. and M. Bjorklund, "Network Configuration Access Control Model", STD 91, RFC 8341, DOI 10.17487/RFC8341, , <https://www.rfc-editor.org/info/rfc8341>.
[RFC8570]
Ginsberg, L., Ed., Previdi, S., Ed., Giacalone, S., Ward, D., Drake, J., and Q. Wu, "IS-IS Traffic Engineering (TE) Metric Extensions", RFC 8570, DOI 10.17487/RFC8570, , <https://www.rfc-editor.org/info/rfc8570>.
[RFC8776]
Saad, T., Gandhi, R., Liu, X., Beeram, V., and I. Bryskin, "Common YANG Data Types for Traffic Engineering", RFC 8776, DOI 10.17487/RFC8776, , <https://www.rfc-editor.org/info/rfc8776>.

Authors' Addresses

Tarek Saad
Cisco Systems Inc
Rakesh Gandhi
Cisco Systems Inc
Xufeng Liu
IBM Corporation
Vishnu Pavan Beeram
Juniper Networks
Igor Bryskin
Individual